Gigabyte GA-EP45T-EXTREME Living Review - Page 3

supershanks · #21 01-09-2008, 16:51

E8600 4,520 8x565@3.33D 1,883 7-7-7-21

Benches

Stability
Not tested

Bios

Code:

GIGABYTE GA-EP45_EXTREME
[u]MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Turbo
CPU Clock Ratio ..........................: 8x
Fine CPU Clock Ratio.....................:.+0.5
CPU Frequency ...........................: 4,520Mhz
Clock Chip Control 
Standard Clock Control
CPU Host Clock Control..................: [Enabled] 
CPU Host Frequency (Mhz) ............:565Mhz
PCI Express Frequency (Mhz) .........:103Mhz
C.I.A. 2.......................................: [Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 700mv
PCI Express Clock Drive.................: 800mv
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)...................: 0ps
DRAM Performance Control
Performance Enhance...................: [Turbo]
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 3.33D
Memory Frequency (Mhz) ..............: 1,883Mhz
DRAM Timing Selectable ................: [Manual] 
Standard Timing Control
CAS Latency Time........................: 7
tRCD .........................................: 7
tRP'...........................................:  7
tRAS..........................................:  21
Advanced Timing Control [Press Enter]
tRRD...........................................:6
tWTR..........................................:17
tWR............................................:22
tRFC...........................................:60
tRTP...........................................:8
Command Rate (CMD) ....................:Auto
Channel A
Static tRead Value.........................:10
 tRD Phase0 Adjustmen...................:Auto
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:8 
Twr2wr(Different Rank)...................:8 
Twr2rd(Different Rank)...................:7
Trd2wr(Same/Diff Rank)..................:9 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps
DDR3 Write Levelling.......................: Enabled
DDR3 Write Training.........................: Enabled
Channel B
Static tRead Value.........................:10
tRD Phase0 Adjustmen.......................:Auto
tRD Phase1 Adjustment......................:Auto
tRD Phase2 Adjustment .....................:Auto
tRD Phase3 Adjustment......................:Auto
Trd2rd(Different Rank).....................:8
Twr2wr(Different Rank).....................:8 
Twr2rd(Different Rank).....................:7
Trd2wr(Same/Diff Rank).....................:9 
Dimm1 Clock Skew Control...................:Auto  ps
Dimm2 Clock Skew Control...................:Auto  ps
DDR3 Write Levelling.......................: Enabled
DDR3 Write Training.........................: Enabled

{U]Motherboard Voltage Control{/U]
Voltage Type.…...……... Normal 
CPU
CPU Vcore….………...........................:1.41875v
CPU Termination…...... 1.200V*...........:1.34 v
CPU PLL………………….........1.500V*...........:1.60 v
MCH/ICH
MCH Core……………..........1.100V............: 1.48v
MCH Reference..…...….….0.800V............; 0.788v
ICH I/O…………....……......1.550V............: 1.540v
DRAM
DRAM Voltage ……........1.500V............: 1.860v
DRAM Termination ...…..0.900V............: 0.940v
Channel A Data Vref ...0.75V.............: 0.790v
Channel B Data Vref ...0.750V............: 0.790v
Channel A Address Vref 0.75V.............: 0.790v
Channel B Address Vref 0.750V............: 0.790v

[b]{U]Advanced Settings[b]{U]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
Note: * refers to 45nm CPU

supershanks · #22 02-09-2008, 13:02

4,388 7.5x585@3.33D 1,950Mhz 7-7-7-21
I was interested particularly in seeing if I could achieve this bench. This matches the highest FSB so far on the DDR2 version. I was wondering if the lack of CPU GTL control might hinder it. Initially I had freezes running Super-Pi, increased MCH Core to 1.50v, the highest so far on both boards

Benches

Stability
So far Benchable only.

Bios

Code:

GIGABYTE GA-EP45T_EXTREME
[u]MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Turbo
CPU Clock Ratio ..........................: 7x
Fine CPU Clock Ratio.....................: +0.5
CPU Frequency ...........................: 4,388Mhz
Clock Chip Control 
Standard Clock Control
CPU Host Clock Control..................: [Enabled] [Disabled]
CPU Host Frequency (Mhz) ............:585Mhz
PCI Express Frequency (Mhz) .........:103Mhz
C.I.A. 2.......................................: [Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 700mv
PCI Express Clock Drive.................: 800mv
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)...................: 0ps
DRAM Performance Control
Performance Enhance...................: [Turbo]
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............:3.33D
Memory Frequency (Mhz) ..............: 1,950Mhz
DRAM Timing Selectable ................: [Manual] 
Standard Timing Control
CAS Latency Time........................: 7
tRCD .........................................: 7
tRP...........................................:  7
tRAS..........................................:  21
Advanced Timing Control [Press Enter]
tRRD...........................................:6
tWTR..........................................:17
tWR............................................:22
tRFC...........................................:60
tRTP...........................................:8
Command Rate (CMD) ....................:Auto
Channel A
Static tRead Value.........................:10
tRD Phase0 Adjustmen.......................:Auto
tRD Phase1 Adjustment......................:Auto
tRD Phase2 Adjustment .....................:Auto
tRD Phase3 Adjustment......................:Auto
Trd2rd(Different Rank).....................:8
Twr2wr(Different Rank).....................:8
Twr2rd(Different Rank).....................:7
Trd2wr(Same/Diff Rank).....................:9
Dimm1 Clock Skew Control...................:Auto  ps
Dimm2 Clock Skew Control...................:Auto  ps
DDR3 Write Levelling.......................: Enabled
DDR3 Write Training.........................: Enabled
Channel B
Static tRead Value.........................:10
tRD Phase0 Adjustmen.......................:Auto
tRD Phase1 Adjustment......................:Auto
tRD Phase2 Adjustment .....................:Auto
tRD Phase3 Adjustment......................:Auto
Trd2rd(Different Rank).....................:8
Twr2wr(Different Rank).....................:8
Twr2rd(Different Rank).....................:7
Trd2wr(Same/Diff Rank).....................:9
Dimm1 Clock Skew Control...................:Auto  ps
Dimm2 Clock Skew Control...................:Auto  ps
DDR3 Write Levelling.......................: Enabled
DDR3 Write Training.........................: Enabled

{U]Motherboard Voltage Control{/U]
Voltage Type.…...……... Normal 
CPU
CPU Vcore….………...........................:1.43125v
CPU Termination…...... 1.200V*...........: 1.34v
CPU PLL………………….........1.500V*...........: 1.62v
MCH/ICH
MCH Core……………..........1.100V............: 1.50v
MCH Reference..…...….….0.800V............; 0.788v
ICH I/O…………....……......1.550V............: 1.540v
DRAM
DRAM Voltage ……........1.500V............: 1.98v
DRAM Termination ...…..0.900V............: 1.04v
Channel A Data Vref ...0.75V.............: 0.87v
Channel B Data Vref ...0.750V............: 0.87v
Channel A Address Vref 0.75V.............: 0.87v
Channel B Address Vref 0.750V............: 0.87v

[b]{U]Advanced Settings[b]{U]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
Note: * refers to 45nm CPU

supershanks · #23 10-09-2008, 18:38

4,440 8x555@3.33D 1,850 7-7-7-20

Benches

Stability

Bios

Code:

GIGABYTE GA-EP45T_EXTREME
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Turbo
CPU Clock Ratio ..........................: 8x
Fine CPU Clock Ratio.....................: +0.0
CPU Frequency ...........................: 4,440Mhz
Clock Chip Control 
Standard Clock Control
CPU Host Clock Control..................: [Enabled] [Disabled]
CPU Host Frequency (Mhz) ............:555Mhz
PCI Express Frequency (Mhz) .........:103Mhz
C.I.A. 2.......................................: [Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 700mv
PCI Express Clock Drive.................: 800mv
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)...................: 0ps
DRAM Performance Control
Performance Enhance...................: [Turbo]
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............:3.33D
Memory Frequency (Mhz) ..............: 1,850Mhz
DRAM Timing Selectable ................: [Manual] 
Standard Timing Control
CAS Latency Time........................: 7
tRCD .........................................: 7
tRP...........................................:  7
tRAS..........................................:  20
Advanced Timing Control [Press Enter]
tRRD...........................................:6
tWTR..........................................:17
tWR............................................:22
tRFC...........................................:60
tRTP...........................................:8
Command Rate (CMD) ....................:Auto
Channel A
Static tRead Value.........................: 9
tRD Phase0 Adjustmen.......................:Auto
tRD Phase1 Adjustment......................:Auto
tRD Phase2 Adjustment .....................:Auto
tRD Phase3 Adjustment......................:Auto
Trd2rd(Different Rank).....................: 8
Twr2wr(Different Rank).....................:8
Twr2rd(Different Rank).....................:7
Trd2wr(Same/Diff Rank).....................:9
Dimm1 Clock Skew Control...................:Auto  ps
Dimm2 Clock Skew Control...................:Auto  ps
DDR3 Write Levelling.......................: Enabled
DDR3 Write Training.........................: Enabled

Channel B
Static tRead Value.........................:Auto
tRD Phase0 Adjustmen.......................:Auto
tRD Phase1 Adjustment......................:Auto
tRD Phase2 Adjustment .....................:Auto
tRD Phase3 Adjustment......................:Auto
Trd2rd(Different Rank).....................:Auto 
Twr2wr(Different Rank).....................:Auto 
Twr2rd(Different Rank).....................:Auto 
Trd2wr(Same/Diff Rank).....................:Auto 
Dimm1 Clock Skew Control...................:Auto  ps
Dimm2 Clock Skew Control...................:Auto  ps
DDR3 Write Levelling.......................: Enabled
DDR3 Write Training.........................: Enabled

Motherboard Voltage Control
Voltage Type.…...……... Normal 
CPU
CPU Vcore….………...........................:1.41875v
CPU Termination…...... 1.200V*...........:1.320 v
CPU PLL………………….........1.500V*...........: 1.60v
MCH/ICH
MCH Core……………..........1.100V............: 1.44v
MCH Reference..…...….….0.800V............; 0.776v
ICH I/O…………....……......1.550V............: 1.540v
DRAM
DRAM Voltage ……........1.500V............: 1.840v
DRAM Termination ...…..0.900V............: 0.970v
Channel A Data Vref ...0.75V.............: 0.800v
Channel B Data Vref ...0.750V............: 0.800v
Channel A Address Vref 0.75V.............: 0.800v
Channel B Address Vref 0.750V............: 0.800v

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
Note: * refers to 45nm CPU

supershanks · #24 11-09-2008, 17:55

4,420 8.5x520@3.33D 1,732 7,7,7,14
Repeated this clock to enable a benchmark comparison. Gigabyte GA-X48T-DQ6

Slightly faster PI32M timing (like for like bench re Cache)
Everest results are similar , though with different versions.
The suprising result for me was Wprime , I've been slightly lazy in that the comparison is E8600 v E8500 (X48T)
, the x48 showing the faster results.

supershanks · #25 12-09-2008, 21:16

4,600 8x575@3.33D 1,917Mhz 7-7-7-21

Benches

Stability
Benches only

Bios

Code:

GIGABYTE GA-EP45T_EXTREME
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Turbo
CPU Clock Ratio ..........................: 8x
Fine CPU Clock Ratio.....................:.+0.0
CPU Frequency ...........................: 4,600Mhz
Clock Chip Control 
Standard Clock Control
CPU Host Clock Control..................: [Enabled] 
CPU Host Frequency (Mhz) ............:575Mhz
PCI Express Frequency (Mhz) .........:103Mhz
C.I.A. 2.......................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 700mv
PCI Express Clock Drive.................: 900mv
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)...................: 0ps

DRAM Performance Control
Performance Enhance...................: [Turbo]
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............:3.33D
Memory Frequency (Mhz) ..............: 1,917Mhz
DRAM Timing Selectable ................: [Manual] 
Standard Timing Control
CAS Latency Time........................: 7
tRCD .........................................: 7
tRP'...........................................:  7
tRAS..........................................:  21
Advanced Timing Control [Press Enter]
tRRD...........................................:6
tWTR..........................................:17
tWR............................................:22
tRFC...........................................:60
tRTP...........................................:8
Command Rate (CMD) ....................:Auto
Channel A

Channel A Timings Settings [Press Enter] 
Static tRead Value.........................:9
 tRD Phase0 Adjustmen...................:Auto
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................: 8 
Twr2wr(Different Rank)...................: 8 
Twr2rd(Different Rank)...................: 7
Trd2wr(Same/Diff Rank)..................: 9
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps
DDR3 Write Levelling........................: Enabled
DDR3 Write Training.........................: Enabled

Channel A Driving Settings [Press Enter] 
Driving Strength Profile:[AUTO]
Data Driving Pull-Up Level.............:Auto 
Cmd Driving Pull-Up Level..............:Auto 
Ctrl Driving Pull-Up Level.............:Auto 
Clk Driving Pull-Up Level..............:Auto 

Data Driving Pull-Down Level...........:Auto 
Cmd Driving Pull-Down Level............:Auto 
Ctrl Driving Pull-Down Level...........:Auto 
Clk Driving Pull-Down Level............:Auto 

Channel B

Channel B Timings Settings [Press Enter] 
Static tRead Value.........................:9
 tRD Phase0 Adjustmen...................:Auto
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................: 8 
Twr2wr(Different Rank)...................: 8 
Twr2rd(Different Rank)...................: 7
Trd2wr(Same/Diff Rank)..................: 9
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps
DDR3 Write Levelling........................: Enabled
DDR3 Write Training.........................: Enabled

Channel B Driving Settings [Press Enter] 
Driving Strength Profile:[AUTO]
Data Driving Pull-Up Level.............:Auto 
Cmd Driving Pull-Up Level..............:Auto 
Ctrl Driving Pull-Up Level.............:Auto 
Clk Driving Pull-Up Level..............:Auto 

Data Driving Pull-Down Level...........:Auto 
Cmd Driving Pull-Down Level............:Auto 
Ctrl Driving Pull-Down Level...........:Auto 
Clk Driving Pull-Down Level............:Auto 

{U]Motherboard Voltage Control{/U]
Voltage Type.………... Normal 
CPU
CPU Vcore….……….........................:1.475v
CPU Termination…..... 1.200V*.......: 1.340v
CPU PLL…………………....1.500V*.......: 1.620v
MCH/ICH
MCH Core……………........1.100V...........:1.480 v
MCH Reference….……....0.800V...........; 0.788v
ICH I/O………………........1.550V............: 1.540v

DRAM
DRAM Voltage …….........1.500V...........: 1.960v
DRAM Termination .….....0.900V...........: 1.030v
Channel A Data VRef......0.750V...........: 0.860v
Channel B Data.VRef .....0.750V...........: 0.860v
Channel A Address Ref....0.750V...........: 0.860v
Channel B Address Ref....0.750V...........: 0.860v

[b]{U]Advanced Settings[b]{U]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
Note: * refers to 45nm CPU

Update - 13/09/2008
Interesting tweak tried tightening
Trd2wr(Same/Diff Rank)..................: 9 --> 8
Re running Everest gives a nice boost in copy from 10836 to 11099 +263 2.4%

supershanks · #26 12-09-2008, 23:03

Auto Voltage Settings
Our friend Alcibiades bought this matter up
Safe Auto Voltages using a moderate overclock, such as anyone might do coming new to the board.

I decided to test it out myself :-
4,050 9x450

All voltages left on auto

Voltages per Easytune - As you see both PLL & Vtt at 1.76v & 1.50v are a little excessive

So suggest you stick with manual settings for both these. Vtt of 1.34v has taken me up to 585fsb with PLL at a maximum of 1.64v so far.

eva2000 · #27 13-09-2008, 18:25

not entirely sure the values shown in easytune6 are the real values ??? have you measured them via DMM ?

supershanks · #28 13-09-2008, 21:29

Quote:

not entirely sure the values shown in easytune6 are the real values ??? have you measured them via DMM ?

I think the values shown there are the bios values. For example

shows values I set in bios as opposed to actual monitored values as in Abit Guru. The Key voltages PLL , CPU Terminnation , MCH & Vdimm are right the others are off from bios. The vdimm subvolts are out by around -0.14v .

Haven't got the MM out on the board yet.

supershanks · #29 17-09-2008, 02:18

Just got my hands on this new Bios courtesy of jooney

For some reason flash was a bit hairy, post got in a repeating led sequence C1 C3 02 88.
Had to use sbenrap's Unbrick procedure which was used for the F5A issue on the X48T. Glad to say it worked after removing battery at a bout 3rd attempt.

there are a few assitions as jonney reported:-
Ironically after my flash issues
Dual Bios Recovery Source

Options:-
Hard drive or 2nd bios chip

CPU Reference Voltages

Still no Memory Driving Profiles though

Alcibiades · #30 11-10-2008, 11:56

Revisited my brothers EP45T-EXTREME
flashed to bios F5B
Works with EIST and C1E turned on as well, so with summer upon us here down under, I'm happy with the system now.
Any tips or suggestions are always welcome.

Ambient temp 20C
Idle: 1.328V - 1.312V temp 31C
Load: 1.312V - 1.296V temp 47C

bios to ET6 values a little skewed as usual

Code:

 
GIGABYTE GA-EP45T_EXTREME 
[u]MB Intelligent Tweaker(M.I.T.) 
Robust Graphics Booster ...............: Turbo 
CPU Clock Ratio ..........................:  8
Fine CPU Clock Ratio.....................: 
CPU Frequency ...........................: 4000Mhz 
Clock Chip Control  
Standard Clock Control 
CPU Host Clock Control..................: [Enabled] 
CPU Host Frequency (Mhz) ............: 500Mhz 
PCI Express Frequency (Mhz) .........: 103Mhz 
C.I.A. 2.............................:[Disabled] 
Advanced Clock Control [Press Enter] 
CPU Clock Drive...........................: 900mv 
PCI Express Clock Drive...................: 900mv 
CPU Clock Skew (ps).......................: 300ps 
MCH Clock Skew (ps).......................: 300ps 
DRAM Performance Control 
Performance Enhance....................: [Turbo] 
Extreme Memory Profile (X.M.P.)........:  
(G)MCH Frequency Latch.................: [Auto] 
System Memory Multiplier ..............: 4.00B
Memory Frequency (Mhz) ..............: 2000Mhz 
DRAM Timing Selectable ................: [Manual] [Auto] 
Standard Timing Control 
CAS Latency Time...............................:  9
tRCD ..........................................:  9
tRP'...........................................:   9
tRAS...........................................:   30

Advanced Timing Control [Press Enter] 
tRRD...........................................: 13
tWTR...........................................: 15
tWR............................................: 13
tRFC...........................................: 72
tRTP...........................................: 8
Command Rate (CMD) ............................: Auto
Channel A 

Channel A Timings Settings [Press Enter]  
Static tRead Value......................: 8
 tRD Phase0 Adjustmen...................:Auto 
tRD Phase1 Adjustment...................:Auto 
 tRD Phase2 Adjustment .................:Auto 
 tRD Phase3 Adjustment..................:Auto 
Trd2rd(Different Rank)..................: 9  
Twr2wr(Different Rank)..................: 9  
Twr2rd(Different Rank)..................: 8  
Trd2wr(Same/Diff Rank)..................: 10  
Dimm1 Clock Skew Control................:Auto  ps 
Dimm2 Clock Skew Control................:Auto  ps 
DDR Write Leveling..........................: Enabled
DDR Write Training..........................: Enabled

Channel A Driving Settings [Press Enter]  
Driving Strength Profile:[AUTO] 
Data Driving Pull-Up Level.............:Auto  
Cmd Driving Pull-Up Level..............:Auto  
Ctrl Driving Pull-Up Level.............:Auto  
Clk Driving Pull-Up Level..............:Auto  

Data Driving Pull-Down Level...........:Auto  
Cmd Driving Pull-Down Level............:Auto  
Ctrl Driving Pull-Down Level...........:Auto  
Clk Driving Pull-Down Level............:Auto  

Channel B 

Channel B Timings Settings [Press Enter]  
Static tRead Value.........................: 8 
 tRD Phase0 Adjustmen...................:Auto 
tRD Phase1 Adjustment...................:Auto 
 tRD Phase2 Adjustment .................:Auto 
 tRD Phase3 Adjustment..................:Auto 
Trd2rd(Different Rank)...................: 9  
Twr2wr(Different Rank)..................: 9  
Twr2rd(Different Rank)...................: 8  
Trd2wr(Same/Diff Rank)..................: 10  
Dimm1 Clock Skew Control................:Auto  ps 
Dimm2 Clock Skew Control................:Auto  ps 
DDR Write Leveling..........................: Enabled
DDR Write Training..........................: Enabled

Channel B Driving Settings [Press Enter]  
Driving Strength Profile:[AUTO] 

Data Driving Pull-Up Level.............:Auto  
Cmd Driving Pull-Up Level..............:Auto  
Ctrl Driving Pull-Up Level.............:Auto  
Clk Driving Pull-Up Level..............:Auto  

Data Driving Pull-Down Level...........:Auto  
Cmd Driving Pull-Down Level............:Auto  
Ctrl Driving Pull-Down Level...........:Auto  
Clk Driving Pull-Down Level............:Auto  


{U]Motherboard Voltage Control{/U] 
Voltage Type.…...……... Normal  
CPU 
CPU Vcore….………...........................: 1.3625v 
CPU Termination…...... 1.200V*...........: 1.300v 
CPU PLL………………….........1.500V*...........: 1.500v
CPU Reference 1...................................: 0.841
CPU Reference 2...................................: 0.863
MCH/ICH 
MCH Core……………..........1.100V............: 1.420v 
MCH Reference..…...….….0.750V............: 0.723v
MCH/DRAM Reference.....0.750V............: 1.000V
ICH I/O…………....……......1.500V............: 1.500v 
DRAM 
DRAM Voltage ……........1.500V............: 1.800v 
DRAM Termination ...…..0.750V............: 1.000v 
Channel A Data Vref ...0.750V.............: 1.000v 
Channel B Data Vref ...0.750V.............: 1.000v 
Channel A Address Vref 0.75V.............: 1.000v 
Channel B Address Vref 0.750V............: 1.000v 

[b]{U]Advanced Settings[b]{U] 
Limit CPUID Max. to 3.....................: [Disabled] 
No-Execute Memory Protect............: [Disabled] 
CPU Enhanced Halt (C1E)................: [Disabled] 
C2/C2E State Support....................: [Disabled] 
x C4/C4E State Support..................: [Disabled] 
CPU Thermal Monitor 2(TM2) ...........: [Enabled] 
CPU EIST Function.........................: [Disabled] 
Virtualization Technology................: [Disabled]