Hi guys, I bought this board (ddr2 version) the other day along with a E7300, and this w/e I am doing some initial oc'ing on it
. So far I am not pushing the
FSB or
RAM hard at all and just want to see what I can get out of the E7300. From playing around with it yesterday I have got it seemingly stable at 3.8Ghz (only done 2 hours of orthos, didn't fail, I just stopped it). I ran it overnight at 3.9 and it failed after 35 mins, doh. I should have tested the 3.8 overnight...
Anyhow my target for the
CPU is 4Ghz, not for any reason other than I just want 4 Ghz if I can get it ;P Then when I have reached my target, or as close as I can get, I will work on the
FSB and
RAM to try and squeeze what I can out of them! I have put my system specs and
BIOS settings below, if one of you more experienced people could take a look through and let me know if there are any improvements I can make to get to 4Ghz it would be greatly appreciated
Thanks for reading, and thanks for the amazing living review Supershanks
System specs:
Intel E7300 2.66Ghz / 1.175VID / 1066mhz
FSB / 10x multi
ZALMAN CNPS9700 HSF
GIGABYTE GA-EP45-EXTREME
OCZ ReaperX DDR2 6400
Xigmatek NRP-MC751
PSU (750W CWT
PSU)
9800GX2
Code:
GIGABYTE GA-EP45-EXTREME
[u]MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster .............: Auto
CPU Clock Ratio .....................: 9
Fine CPU Clock Ratio.................: +0.5
CPU Frequency .......................: 3.80 ghz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control...............: Enabled
CPU Host Frequency (Mhz) ............: 400 Mhz
PCI Express Frequency (Mhz) .........: 100 Mhz
C.I.A. 2.............................: Disabled
Advanced Clock Control [Press Enter]
CPU Clock Drive...............800....: 800mv
PCI Express Clock Drive.......900....: 900mv
CPU Clock Skew (ps)...........0......: 0ps
MCH Clock Skew (ps)...........0......: 0ps
DRAM Performance Control
Performance Enhance..................: Standard
Extreme Memory Profile (X.M.P.)......: Disabled
(G)MCH Frequency Latch...............: 400 mhz
System Memory Multiplier ............: 2.00d
Memory Frequency (Mhz) ..............: 800 Mhz
DRAM Timing Selectable ..............: Manual
Standard Timing Control
CAS Latency Time..............?......: 4
tRCD .........................?......: 4
tRP'..........................?......: 3
tRAS..........................?......: 15
Advanced Timing Control [Press Enter]
tRRD..........................?......: 3
tWTR..........................?......: 3
tWR...........................?......: 6
tRFC..........................?......: 46
tRTP..........................?......: 3
Command Rate (CMD) ...........0......: 2T
Channel A
Channel A Timings Settings [Press Enter]
Static tRead Value............8......: 12
tRD Phase0 Adjustmen..........0......: Auto
tRD Phase1 Adjustment.........0......: Auto
tRD Phase2 Adjustment ........0......: Auto
tRD Phase3 Adjustment.........0......: Auto
Trd2rd(Different Rank)........6......: Auto
Twr2wr(Different Rank)........6......: Auto
Twr2rd(Different Rank)........5......: Auto
Trd2wr(Same/Diff Rank)........8......: Auto
Dimm1 Clock Skew Control.............: Auto
Dimm2 Clock Skew Control.............: Auto
DDR3 Write Training .................: Enabled
Channel A Driving Settings [Press Enter]
Driving Strength Profile:............: 800Mhz
Data Driving Pull-Up Level...........: Auto
Cmd Driving Pull-Up Level............: Auto
Ctrl Driving Pull-Up Level...........: Auto
Clk Driving Pull-Up Level............: Auto
Data Driving Pull-Down Level.........: Auto
Cmd Driving Pull-Down Level..........: Auto
Ctrl Driving Pull-Down Level.........: Auto
Clk Driving Pull-Down Level..........: Auto
Channel B
Channel B Timings Settings [Press Enter]
Static tRead Value............8......: 12
tRD Phase0 Adjustmen..........0......: Auto
tRD Phase1 Adjustment.........0......: Auto
tRD Phase2 Adjustment ........0......: Auto
tRD Phase3 Adjustment.........0......: Auto
Trd2rd(Different Rank)........6......: Auto
Twr2wr(Different Rank)........6......: Auto
Twr2rd(Different Rank)........5......: Auto
Trd2wr(Same/Diff Rank)........8......: Auto
Dimm1 Clock Skew Control.............: Auto
Dimm2 Clock Skew Control.............: Auto
DDR3 Write Training .................: Enabled
Channel B Driving Settings [Press Enter]
Driving Strength Profile:............: 800Mhz
Data Driving Pull-Up Level...........: Auto
Cmd Driving Pull-Up Level............: Auto
Ctrl Driving Pull-Up Level...........: Auto
Clk Driving Pull-Up Level............: Auto
Data Driving Pull-Down Level.........: Auto
Cmd Driving Pull-Down Level..........: Auto
Ctrl Driving Pull-Down Level.........: Auto
Clk Driving Pull-Down Level..........: Auto
{U]Motherboard Voltage Control{/U]
Voltage Type........ Normal
CPU
CPU Vcore...................1.175v...: 1.42500v (can go lower but this gives me 1.360v at load)
CPU Termination.............1.200V...: 1.2v
CPU PLL.....................1.500V...: 1.500v
CPU Reference...............0.76V....: Auto
CPU Reference2..............0.80V....: Auto
MCH/ICH
MCH Core....................1.100V...: 1.24000v
MCH Reference...............0.76V....: Auto
MCH/DRAM Ref................0.900V...: Auto
ICH I/O.....................1.500V...: 1.540v
ICH Core....................1.100V...: 1.100v
DRAM
DRAM Voltage................1.800V...: 2.1000v
DRAM Termination............0.900V...: Auto
Channel A Reference.........0.900V...: Auto
Channel B Reference.........0.900V...: Auto
[b]{U]Advanced Settings[b]{U]
Limit CPUID Max. to 3................: Disabled
No-Execute Memory Protect............: Disabled
CPU Enhanced Halt (C1E)..............: Disabled
CPU Thermal Monitor(TM) .............: Disabled
CPU EIST Function....................: Disabled
Note: screenshot below has something like 1.38vcore in
BIOS and the min temps are high because I didn't load realtemp until just after starting orthos.
Please help! ;)
no email was late 
Linear Mode
