Gigabyte GA-EP45-EXTREME Living Review - Page 11

supershanks · #**101** 02-08-2008, 17:30

555x7.5@2.0B 1,111 5,5,5,20

Benches

For some reason Memset isn't showing tRD(Performance)
Per Everest:-

Stability

Bios Settings

Code:

GIGABYTE GA-EP45_EXTREME
[u]MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Turbo
CPU Clock Ratio ..........................: 7
Fine CPU Clock Ratio.....................:.+0.5
CPU Frequency ...........................: 4,160Mhz
Clock Chip Control 
Standard Clock Control
CPU Host Clock Control..................: [Enabled] 
CPU Host Frequency (Mhz) ............:555Mhz
PCI Express Frequency (Mhz) .........:103Mhz
C.I.A. 2.......................................: Disabled
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................:700mv
PCI Express Clock Drive.................:700mv
CPU Clock Skew (ps)....................: 200ps
MCH Clock Skew (ps)...................: 0ps
DRAM Performance Control
Performance Enhance...................: [Turbo]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.00B
Memory Frequency (Mhz) ..............: 1,110Mhz
DRAM Timing Selectable ................: [Manual] 
Standard Timing Control 
CAS Latency Time........................: 5
tRCD .........................................: 5
tRP'...........................................:  5
tRAS..........................................:  20
Advanced Timing Control [Press Enter]
tRRD...........................................:4
tWTR..........................................:4
tWR............................................:8
tRFC...........................................:54
tRTP...........................................:4
Command Rate (CMD) ....................:Auto
Channel A
Static tRead Value.........................: Auto = 10
 tRD Phase0 Adjustmen...................:Auto 0
tRD Phase1 Adjustment...................:Auto 0
 tRD Phase2 Adjustment .................:Auto 0
 tRD Phase3 Adjustment..................:Auto 0
Trd2rd(Different Rank)....................:Auto 8
Twr2wr(Different Rank)...................:Auto 8
Twr2rd(Different Rank)...................:Auto 7
Trd2wr(Same/Diff Rank)..................:Auto 9
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

Channel B
Static tRead Value.........................: Auto = 10
 tRD Phase0 Adjustmen...................:Auto 0
tRD Phase1 Adjustment...................:Auto 0
 tRD Phase2 Adjustment .................:Auto 0
 tRD Phase3 Adjustment..................:Auto 0
Trd2rd(Different Rank)....................:Auto 8
Twr2wr(Different Rank)...................:Auto 8
Twr2rd(Different Rank)...................:Auto 7
Trd2wr(Same/Diff Rank)..................:Auto 9
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

{U]Motherboard Voltage Control{/U]
Voltage Type.………... Normal 
CPU
CPU Vcore….……….........................:1.40625v
CPU Termination…..... 1.200V*.......: 1.32v
CPU PLL…………………....1.500V*.......: 1.60v
CPU Referen.…………....0.755V*.......: 0.800v
CPU Reference2………,,0.800V*.......:0.836v
MCH/ICH
MCH Core…………….....1.100V...........: 1.360v
MCH Reference….…….0.800V...........; 0.776v
MCH/DRAM Ref.…......0.900V...........: 0.97v
ICH I/O……………….....1.550V............: 1.54v
ICH Core…………...……1.100V............: 1.10v
DRAM
DRAM Voltage ……....1.800V............: 2.220v
DRAM Termination .…0.900V............: 0.97v
Channel A Reference 0.900V............: 0.97v
Channel B Reference 0.900V............: 0.97v
[b]{U]Advanced Settings[b]{U]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
Note: * refers to 45nm CPU

Ace-a-Rue · #**102** 03-08-2008, 02:41

Quote:

Originally Posted by supershanks

Eva raised the matter of these chips interfering with backplates.

I didn't have the board at the time, so could only look at pictures. Have done a bit of research since :-

1) Thermalright Bolt Through
There is as George pointed out some interference. It isn't to noticeable but does give cause for concern

2) Scythe Universal Retention Kit
I'm lucky 'cos I had a couple of these kits

The backing plate on this very rigid steel , seems firmer than the Thermalright, but it also has an equal depth layer of neophane with a final layer of paper on top.

Side view showing the 2 layers.

I'm using 1 with my EP45 & my Fuzion block. A 2nd works well with the XIGMATEK HDT-S1283 on the EP45T.

This shot of the baseplate after unmounting, shows it's working pretty well
Gave a good impression anyway

very nice!...your pictures would take a big load off anyone's mind to know they can get around this problem.

supershanks · #**103** 03-08-2008, 10:38

Hi Ace,

Quote:

very nice!...your pictures would take a big load off anyone's mind to know they can get around this problem.

That'll be good, but I don't think its's a big issue the plastic chips feel very solid are are aligned , are capable of taking pressure as
Alcibiades

Quote:

I installed a Thermalright Ultra 120 Extreme on the EP45-extreme and the EP45T-extreme using stock everything, I was not gentle either when mounting those spring loaded screws, but encountered no problems at all.

and I found initially. It's good to know there are options if you are concerned. Nothing to stop you cutting a Neoprene Rubber gasket to use with the thermalright bolt thru

supershanks · #**104** 03-08-2008, 23:36

565x7.5@2.0B 1,130 5,5,5,24

These last 2 clocks have been a bit odd, I started off aiming at 480x7.5 , but struggled to get ram stability.
With this clock I've dropped MCH Reference to 0.756. so the 3 Gtlrefs are now 60.6%, 63.3% 57.3% CPU Reference1, CPU Reference2 & MCH Reference

Benches

Per Everest:-

Stability

Bios Settings

Code:

GIGABYTE GA-EP45_EXTREME
[u]MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Turbo
CPU Clock Ratio ..........................: 7
Fine CPU Clock Ratio.....................:.+0.5
CPU Frequency ...........................: 4,230Mhz
Clock Chip Control 
Standard Clock Control
CPU Host Clock Control..................: [Enabled] 
CPU Host Frequency (Mhz) ............:565Mhz
PCI Express Frequency (Mhz) .........:103Mhz
C.I.A. 2.......................................: Disabled
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................:700mv
PCI Express Clock Drive.................:700mv
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)...................: 0ps
DRAM Performance Control
Performance Enhance...................: [Turbo]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.00B
Memory Frequency (Mhz) ..............: 1,130Mhz
DRAM Timing Selectable ................: [Manual] 
Standard Timing Control 
CAS Latency Time........................: 5
tRCD .........................................: 5
tRP'...........................................:  5
tRAS..........................................:  24
Advanced Timing Control [Press Enter]
tRRD...........................................:4
tWTR..........................................:4
tWR............................................:8
tRFC...........................................:52
tRTP...........................................:4
Command Rate (CMD) ....................:Auto
Channel A
Static tRead Value.........................: Auto = 10
 tRD Phase0 Adjustmen...................:Auto 0
tRD Phase1 Adjustment...................:Auto 0
 tRD Phase2 Adjustment .................:Auto 0
 tRD Phase3 Adjustment..................:Auto 0
Trd2rd(Different Rank)....................:Auto 8
Twr2wr(Different Rank)...................:Auto 8
Twr2rd(Different Rank)...................:Auto 7
Trd2wr(Same/Diff Rank)..................:Auto 9
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

Channel B
Static tRead Value.........................: Auto = 10
 tRD Phase0 Adjustmen...................:Auto 0
tRD Phase1 Adjustment...................:Auto 0
 tRD Phase2 Adjustment .................:Auto 0
 tRD Phase3 Adjustment..................:Auto 0
Trd2rd(Different Rank)....................:Auto 8
Twr2wr(Different Rank)...................:Auto 8
Twr2rd(Different Rank)...................:Auto 7
Trd2wr(Same/Diff Rank)..................:Auto 9
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

{U]Motherboard Voltage Control{/U]
Voltage Type.………... Normal 
CPU
CPU Vcore….……….........................:1.4125v
CPU Termination…..... 1.200V*.......: 1.32v
CPU PLL…………………....1.500V*.......: 1.60v
CPU Referen.…………....0.755V*.......: 0.800v
CPU Reference2………,,0.800V*.......:0.836v
MCH/ICH
MCH Core…………….....1.100V...........: 1.380v
MCH Reference….…….0.800V...........; 0.756v
MCH/DRAM Ref.…......0.900V...........: 1.010v
ICH I/O……………….....1.550V............: 1.54v
ICH Core…………...……1.100V............: 1.10v
DRAM
DRAM Voltage ……....1.800V............: 2.220v
DRAM Termination .…0.900V............: 1.010v
Channel A Reference 0.900V............: 1.010v
Channel B Reference 0.900V............: 1.010v
[b]{U]Advanced Settings[b]{U]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
Note: * refers to 45nm CPU

Ace-a-Rue · #**105** 06-08-2008, 01:36

hmmmm, the Biostar TPower seems to be a VERY good board...it was a slow start to figure out the bios settings...i think i have it down pretty good.

the board comes right up to being neck and neck with the X48T and i am only running the VC at 8X link speed since i have an Areca Raid card in the 2nd slot running at 8X.

UNOFFICIAL BIOSTAR TPower I45 M/B - Page 2 - XtremeSystems Forums

supershanks · #**106** 06-08-2008, 01:55

That's looking good Ace

that 32m Pi looks a real good time.

Ace-a-Rue · #**107** 06-08-2008, 03:45

yes!..the 32M surprised me...the board just gives you that burst of speed...i am going to put the other drives on the areca card; the ones i used in the PCMARK 2005 showdown between the X48T and IP35 Pro to eliminate any doubt about its true performance...i want to make sure the Veloci-Raptors are not adding an extra burst of speed somewhere...you wouldn't think it would except in the PCMARK 2005 bench...the video benches and SuperPI should stay the same.