DFI UT X48-T3RS LanParty - Living Review

[Clunk]

Welcome to the forums

Switch it all off and unplug the PSU, flip the battery out, press the on/off switch to discharge any current then leave for a while (couple of hours if possible).

Then power on and try again.

If you are using any settings from CMOS reloaded that were saved with a different BIOS version, delete them and start again.

Also, make sure you have the latest BIOS.

Before overclocking again, you could give the sticks a run through memtest86+ v.2.xx to make sure they are ok.

If they are ok, try them in the other slots.

[mrt181]

i have reseted my motherboard with the board jumper. it works with stock settings. will check the ram and try again.

[Clunk]

Weiser, I have moved your posts to their own thread here as it doesn't appear to be related to the motherboard.

[mrt181]

i have tried for a lower FSB 400 overclock because i could not get those settings from BlackDragon24 and davidk21770 from thd dficlub to work. it either did not post or crashed with different BSOD and missing file errors the moment the os was going to be loaded.

Here are some settings.



EDIT:

CPU Feature Page
Thermal Management Control................Enabled
PPM (EIST) Mode...........................Enabled
Limit CPUID MaxVal........................Disabled
CIE Function..............................Auto
Execute Disable Bit.......................Enabled
Virtualization Technology.................Enabled
Core Multi-Processing.....................Enabled

Main BIOS Page
Exist Setup Shutdown......................Mode 2
Shutdown After AC Loss....................Disabled
O. C. Fail Retry Counter..................0
CPU Clock Ratio...........................8.5x
CPU N/2 Ratio.............................Enabled
CPU Clock.................................400 MHz
Boot Up Clock.............................Auto
CPU Clock Amplitude.......................800mV
CPU Clock0 Skew...........................0ps
CPU Clock0 Skew...........................0ps
DRAM Speed................................333/1333
PCIE Clock................................100MHz
PCIE Slot Config..........................1X 1X

CPU Spread Spectrum.......................Disabled
PCIE Spread Spectrum......................Disabled

Voltage Setting Page 
CPU VID Control...........................Auto 1.2450V
CPU VID Special Add Limit.................Disabled
CPU VID Special Add.......................104.48%
DRAM Voltage Control......................1.874V
SB Core/CPU PLL Voltage...................1.510V
NB Core Voltage...........................1.555V
CPU VTT Voltage...........................1.300V
VCore Droop Control.......................Enabled
Clockgen Voltage Control..................3.45V
GTL+ Buffers Strength.....................Strong
Host Slew Rate............................Strong
GTL REF Voltage Control...................Disable
CPU GTL 1/2 REF Volt......................121
CPU GTL 0/3 REF Volt......................113
North Bridge GTL REF Volt ................80

DRAM Timing Page
Enhance Data Transmitting.................Fast
Enhance Addressing........................Normal
T2 Dispatch...............................Disabled

CAS Latency Time (tCL)....................Auto
RAS# to CAS# Delay (tRCD).................Auto
RAS# Precharge (tRP)......................Auto
Precharge Delay (tRAS)....................Auto
All Precharge to Act......................Auto
REF to ACT Delay (tRFC)...................Auto
Performance Level.........................Auto
Read Delay Phase Adjust...................(All Auto)
MCH ODT Latency...........................Auto
Write to PRE Delay (tWR)..................Auto
Rank Write to Read (tWTR).................Auto
ACT to ACT Delay (tRRD)...................Auto
Read to Write Delay (tRDWR)...............Auto
Ranks Write to Write (tWRWR)..............Auto
Ranks Read to Read (tRDRD)................Auto
Ranks Write to Read (tWRRD)...............Auto
Read CAS# Precharge (tRTP)................Auto
ALL PRE to Refresh........................Auto
XMP Support...............................Disabled

Clock Setting Fine Delay..................Listed Below
Read Delay Phase Adjust Page
Channel 1 Phase 0 Pull-In.................Auto
Channel 1 Phase 1 Pull-In.................Auto
Channel 1 Phase 2 Pull-In.................Auto
Channel 1 Phase 3 Pull-In.................Auto
Channel 1 Phase 4 Pull-In.................Auto

Channel 2 Phase 0 Pull-In.................Auto
Channel 2 Phase 1 Pull-In.................Auto
Channel 2 Phase 2 Pull-In.................Auto
Channel 2 Phase 3 Pull-In.................Auto
Channel 2 Phase 4 Pull-In.................Auto

Clock Setting Fine Delay Page
DRAM CLK Driving Strength...............  Level 6
DRAM Data Driving Strength................Level 8
Ch1 DLL Default Skew Model................Model 0
Ch2 DLL Default Skew Model................Model 0

Fine Delay Step Degree....................5ps


Ch1 Clock Crossing Setting................Auto
DIMM 1 Clock fine delay...................Current 489ps
DIMM 2 Clock fine delay...................Current 489ps
DIMM 1 Control fine delay.................Current 434ps
DIMM 2 Control fine delay.................Current 473ps
Ch 1 Command fine delay...................Current 205ps

Ch2 Clock Crossing Setting................Auto
DIMM 3 Clock fine delay...................Current 686ps
DIMM 4 Clock fine delay...................Current 686ps
DIMM 3 Control fine delay.................Current 607ps
DIMM 4 Control fine delay.................Current 654ps
Ch 2 Command fine delay...................Current 182ps

Ch1Ch2 CommonClock Setting................Auto

Ch1 RDCAS GNT-Chip Delay..................Auto
Ch1 WRCAS GNT-Chip Delay..................Auto
Ch1 Command to CS Delay...................Auto

Ch2 RDCAS GNT-Chip Delay..................Auto
Ch2 WRCAS GNT-Chip Delay..................Auto
Ch2 Command to CS Delay...................Auto

Common CMD to CS Timing...................Auto

What next to reach a stable FSB 424 MHz OC?

EDIT: Getting BSOD during Deskop and 3dMark06 -> BAD_POOL_HEADER amd MEMORY_MANAGEMENT. Will try

DRAM Timing Page
Enhance Data Transmitting.................Normal
Enhance Addressing........................Normal

Clock Setting Fine Delay Page
DRAM CLK Driving Strength...............  Level 6
DRAM Data Driving Strength................Level 6

EDIT: 18305 points in 3DMark06, still much to do. Seems to be stable for the moment.
EDIT: 10186 points in 3DMarkVantage@PERFORMANCE, 13445 for CPU.

[WeiserRiese]

hey

can I lose my raid data if I upgrade my bios?

[WILSON]

No you will be fine ive never lost mine after a bios update just remember to load up the settings again b4 you boot in to windows.

[WeiserRiese]

another question xD:

if I install my windows again ... will I lose my data on raid 1? (windows is on singe disc)

[supershanks]

are you running matrix raid with 2 stripes ?
Raid 0 with with windows on 1st stripe
Raid 1 with data on 2nd stripe ??
If the above then no you can just delete or reformat the raid0 partition , or even delete & rebuild the 1st stripe.
without losing the 2nd. I would be inclined to back it up though.

[WeiserRiese]

ok ... I got:

1 WD raptor .... here is windows.
and
2 seagate 1tb harddrives (as a raid 1)


now I install windows on the raptor again ... would anything happen to my raid 1?

[mrt181]

no but to not mess something up during installation and selection of disks just unplug the raid. better save than sorry