DFI UT X48-T3RS LanParty - Living Review - Page 42

eva2000 · #**411** 13-09-2008, 18:26

maybe try 8/29 official bios ?

DDR3-2133 sweetness

System specs

Intel Core 2 Duo E8600 Q820A599 *5146
Corsair Nautilus 500
DFI LP UT X48-T3RS 8/29 official bios
NB Cooling: Thermalright HR-05 + 80x25mm Sunon 49cfm fan
2x 512MB HIS IceQ3 Turbo HD3850 Crossfire in PCI-E 1 & 3 slots (x16 + x16)
2x1GB Corsair TW3X2G2133C9DF Dominator 9-9-9-24 at 2.0v rated (Samsung ICs)
750GB Samsung HD753LJ
Pioneer DVD-RW
620W Corsair HX620
WinXP Pro SP2

Board FSB limited to 500-510FSB so no way to hit rated mem speeds yet.. but will try other boards soon

8/29 official bios

Code:

PC Health Status
Adjust CPU Temp: -6C

CPU Feature
- Thermal Management Control: Disabled
-  PPM(EIST) Mode: Disabled
- Limit CPUID MaxVal: Disabled
- CIE Function: Disabled
- Virtualization Technology: Disabled
- Core Multi-Processing: Enabled

Exist Setup Shutdown: Mode 2
Shutdown after AC Loss: Disabled
O.C. Fail retry Counter 0
CPU Clock Ratio: 8x
CPU N/2 Ratio: Disabled
Target CPU Clock:
CPU Clock: 500
Boot Up Clock: AUTO
CPU Clock Amplitude: 800mv
CPU Clock0 Skew: 0ps
CPU Clock1 Skew: 0ps
DRAM Speed: 400/1600
- Target DRAM Speed: DDR3-1000
PCIE Clock: 100mhz
PCIE Slot Config: 1X 1X

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
SATA Spread Spectrum: Disabled

Voltage Settings
CPU VID Control: 1.18750v
COY VID Special Add Limit: Enabled
CPU VID Special Add: AUT0
DRAM Voltage Control: 1.915v
SB Core/CPU PLL Voltage: 1.51
NB Core Voltage: 1.566
CPU VTT Voltage: 1.300
Vcore Droop Control: Enabled
Clockgen Voltage Control: 3.45v
GTL+ Buffers Strength: Strong
Host Slew Rate: Weak
x MCH RON Offset Value:
x MCH RTT Offset Value:
x MCH Slew Rate Offset Value:
x MCH VREF 1 Value:
x MCH VREF 2 Value: 
x MCH VREF 3 Value:

GTL REF Voltage Control: Disable
x CPU GTL 1/2 REF Volt: 113
x CPU GTL 0/3 REF Volt: 100
x North Bridge GTL REF Volt: 100

DRAM Timing
- DRAM CLK Driving Strength: Level 6
- DRAM DATA Driving Strength: Level 8
- Ch1 DLL Default Skew Model: Model 1
- Ch2 DLL Default Skew Model: Model 1
- Enhance Data transmitting: AUTO
- Enhance Addressing: FAST
- T2 Dispatch: Enabled

Fine Delay Step Degree: 5ps to 80ps

Clock Setting Fine Delay
Ch1 Clock Crossing Setting: Aggressive
- DIMM 1 Clock fine delay: Current 329ps
- DIMM 2 Clock fine delay: Curren 329ps
- DIMM 2 Control fine delay: Current 294ps
- DIMM 1 Control fine delay: Current 259ps
- Ch 1 Command fine delay: Current 273ps

Ch2 Clock Crossing Setting: Aggressive
- DIMM 3 Clock fine delay: Current 469ps
- DIMM 4 Clock fine delay: Current 469ps
- DIMM 4 Control fine delay: Current 406ps
- DIMM 3 Control fine delay: Current 322ps
- Ch 2 Command fine delay: Current 329ps

Ch1Ch2 CommonClock Setting: Aggressive

Ch1 RDCAS GNT-Chip Delay: Auto
Ch1 WRCAS GNT-Chip Delay: Auto
Ch1 Command to CS Delay: Auto

Ch2 RDCAS GNT-Chip Delay: Auto
Ch2 WRCAS GNT-Chip Delay: Auto
Ch2 Command to CS Delay: Auto

Common CMD to CS Timing: 1N

CAS Latency Time (tCL): 8
RAS# to CAS# Delay (tRCD): 8
RAS# Precharge (tRP): 8
Precharge Delay (tRAS): 21
All Precharge to Act: AUTO
REF to ACT Delay (tRFC): AUTO
Performance LVL (Read Delay) (tRD): AUTO

Read delay phase adjust: Enter

Ch1 Read delay phase (4~0)
- Channel 1 Phase 0 Pull-In: AUTO
- Channel 1 Phase 1 Pull-In: AUTO
- Channel 1 Phase 2 Pull-In: AUTO
- Channel 1 Phase 3 Pull-In: AUTO
- Channel 1 Phase 4 Pull-In: AUTO

Ch2 Read delay phase (4~0)
- Channel 2 Phase 0 Pull-In: Auto
- Channel 2 Phase 1 Pull-In: Auto
- Channel 2 Phase 2 Pull-In: Auto
- Channel 2 Phase 3 Pull-In: Auto
- Channel 2 Phase 4 Pull-In: Auto

MCH ODT Latency: AUTO
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Read to Write Delay (tRDWR): AUTO
Ranks Write to Write (tWRWR): AUTO
Ranks Read to Read (tRDRD): AUTO
Ranks Write to Read (tWRRD): AUTO
Read CAS# Precharge (tRTP): AUTO
ALL PRE to Refresh: AUTO
XMP Support: Disabled

Clunk · #**412** 13-09-2008, 18:55

Still no 500fsb+ / 2000+ though on the T3RS?

WeiserRiese · #**413** 13-09-2008, 19:43

Hi

I bought the DFI Lanparty UT X48-T3RS and the OCZ3RPR13334G, but when i start, there is even the C1 code.

can i get the RAM working if I update the bios?

Yours
WeiserRiese

Clunk · #**414** 13-09-2008, 20:00

Welcome to the forums

Please add your system specs to your profile - click on the big green link in my sig

I see your memory is CAS6, I'm not sure if CAS6 is a problem for the shipping BIOS, I know CAS7 is.

You could also try one stick at a time, you may just have a bad stick.

WeiserRiese · #**415** 13-09-2008, 20:02

I tested every stick at every slot, even C1

WeiserRiese · #**416** 13-09-2008, 21:17

or do you perhaps know a ram modul (2x2gb) which works propably?

Clunk · #**417** 13-09-2008, 22:24

As far as I know, some OCZ modules won't work, such as the special ops, some G.Skill and all CAS7 rated modules.

There may be others, but that's all I know of.

Ones that do work are the Corsair 9-9-9-24 4gb kit, the OCZ 2000MHz kit was ok, but OCZ do not support them when used on this board, in other words, if you can't hit 2000MHz, it's not their fault