DFI UT X48-T3RS LanParty - Living Review

[Clunk]

Originally Posted by Nowaka

Btw, will this board be able to run DFI's new ABS bios thingy?

It's not for the LT/UT at the moment

[Praz]

Originally Posted by Nowaka

Nice with the 500/2000 Praz Are you able to go higher?

Didn't try. Just getting the settings nailed down for the EB and ReaperX sticks to try to run them together.

Some OCZ 1600EB 2x1GB sticks using the 06/09 BIOS. The BIOS won't allow the board to boot with anything other the CAS 9 and requires quite a bit of NB voltage.


click for larger image



click for larger image

[Nibbler1(from ROT)]

MAX FSB = 520MHz(BIOS 620) ....... it`s not monsteR, it` a pussycat on this time


memory: 2*1GB Micron-D9GTR

CPU Feature Page
Thermal Management Control................Disabled
PPM (EIST) Mode...........................Disabled
Limit CPUID MaxVal........................Disabled
CIE Function..............................Disabled
Virtualization Technology.................Disabled
Core Multi-Processing.....................Enabled

Main BIOS Page
Exist Setup Shutdown......................Mode 2
Shutdown After AC Loss....................Disabled
O. C. Fail Retry Counter..................0
CPU Clock Ratio...........................6x
CPU N/2 Ratio.............................Disabled
CPU Clock.................................520 MHz
Boot Up Clock.............................Auto
CPU Clock Amplitude.......................800mV
CPU Clock0 Skew...........................100ps
CPU Clock0 Skew...........................100ps
DRAM Speed................................400/1333
PCIE Clock................................101MHz
PCIE Slot Config..........................1X 1X

CPU Spread Spectrum.......................Disabled
PCIE Spread Spectrum......................Disabled

Voltage Setting Page 
CPU VID Control...........................1.3875V
CPU VID Special Add Limit.................Enabled
CPU VID Special Add.......................Auto
DRAM Voltage Control......................2.11V
SB Core/CPU PLL Voltage...................1.510V
NB Core Voltage...........................1.665V
CPU VTT Voltage...........................1.453V
VCore Droop Control.......................Enabled
Clockgen Voltage Control..................3.60V
GTL+ Buffers Strength.....................Strong
Host Slew Rate............................Strong
GTL REF Voltage Control...................Enable
CPU GTL 1/2 REF Volt......................123
CPU GTL 0/3 REF Volt......................114
North Bridge GTL REF Volt ................94

DRAM Timing Page
Enhance Data Transmitting.................Auto
Enhance Addressing........................Auto
T2 Dispatch...............................Auto
CAS Latency Time (tCL)....................7
RAS# to CAS# Delay (tRCD).................6
RAS# Precharge (tRP)......................5
Precharge Delay (tRAS)....................15
All Precharge to Act......................Auto
REF to ACT Delay (tRFC)...................Auto
Performance Level.........................10
MCH ODT Latency...........................Auto
Write to PRE Delay (tWR)..................Auto
Rank Write to Read (tWTR).................Auto
ACT to ACT Delay (tRRD)...................Auto
Read to Write Delay (tRDWR)...............Auto
Ranks Write to Write (tWRWR)..............Auto
Ranks Read to Read (tRDRD)................Auto
Ranks Write to Read (tWRRD)...............Auto
Read CAS# Precharge (tRTP)................Auto
ALL PRE to Refresh........................Auto

Read Delay Phase Adjust Page
Channel 1 Phase 0 Pull-In.................Enabled
Channel 1 Phase 1 Pull-In.................Enabled
Channel 1 Phase 2 Pull-In.................Enabled
Channel 1 Phase 3 Pull-In.................Enabled
Channel 1 Phase 4 Pull-In.................Enabled

Channel 2 Phase 0 Pull-In.................Auto
Channel 2 Phase 1 Pull-In.................Auto
Channel 2 Phase 2 Pull-In.................Auto
Channel 2 Phase 3 Pull-In.................Auto
Channel 2 Phase 4 Pull-In.................Auto

Clock Setting Fine Delay Page
Ch1 DLL Default Skew Model...................Model 3
Ch2 DLL Default Skew Model...................Model 3

Fine Delay Step Degree....................5ps


Ch1 Clock Crossing Setting................Auto
DIMM 1 Clock fine delay...................Current 489ps
DIMM 2 Clock fine delay...................Current 489ps
DIMM 1 Control fine delay.................Current 434ps
DIMM 2 Control fine delay.................Current 473ps
Ch 1 Command fine delay...................Current 560ps

Ch2 Clock Crossing Setting................Auto
DIMM 3 Clock fine delay...................Current 686ps
DIMM 4 Clock fine delay...................Current 686ps
DIMM 3 Control fine delay.................Current 607ps
DIMM 4 Control fine delay.................Current 654ps
Ch 2 Command fine delay...................Current 693ps

Ch1Ch2 CommonClock Setting................Auto

Ch1 RDCAS GNT-Chip Delay..................Auto
Ch1 WRCAS GNT-Chip Delay..................Auto
Ch1 Command to CS Delay...................Auto

Ch2 RDCAS GNT-Chip Delay..................Auto
Ch2 WRCAS GNT-Chip Delay..................Auto
Ch2 Command to CS Delay...................Auto

Common CMD to CS Timing...................2N

[Nowaka]

I will be using a intel Q9450 for my next pc.. do you think that i would be able to get higher cpu clocks with a DDR2 DFI mobo than with this DDr3 mobo?

[Praz]

Originally Posted by Nowaka

I will be using a intel Q9450 for my next pc.. do you think that i would be able to get higher cpu clocks with a DDR2 DFI mobo than with this DDr3 mobo?

Almost without exception the limiting component will be the Q9450, not the board.

[Nowaka]

Okay.. so whilst i'm going with the Q9450, i'm better set with a DDR2 mobo, right? if i can't feel any difference between DDR2 and DDR3, it would be stupid to purchase this DDR3 mobo..

[Praz]

All voltages, fans and temps are now displayed. A couple of the voltage readings are off though. It is being worked on.

Everest Ultimate Beta

[Clunk]

Thanks Praz, much appreciated

[SFB]

Hi Clunk,
sorry for my bad english, I have a problem with this mobo, randomly the computer turn off and the bios post code sign CF. I don't understand what means CF. Can You help me?
thanks.

[supershanks]

Hi SFB,
Welcome to the Forum
See DFI POst Code Errors for explanation of CF. Looks Like your memory may be causing issues