DFI UT X48-T3RS LanParty - Living Review - Page 15

supershanks · #**141** 21-06-2008, 19:34

Quote:

It's only fair that someone else gets the curse for a while

Just tell me who to pass it onto , will ya . I've had my share I reckon 4 in about 6 weeks is enough for anyone

Clunk · #**142** 21-06-2008, 19:52

supershanks · #**143** 21-06-2008, 19:56

You can read minds

Have just been working the necessary voodoo

supershanks · #**144** 21-06-2008, 20:24

RMA request done, there's a chance they might get the bios out

Quote:

You will receive a separate email within 3 working days indicating the result of
your service request together with further instructions on how to proceed.

probably looking at 10~12 days I guess + the 3 day wait.

Praz · #**145** 21-06-2008, 20:32

E8400
DFI LP UT X48-T3RS, 06/09 BIOS
480x8.5, Memory 1600MHz
2x2GB OCZ PC3-10666 1333MHz ReaperX
XFX8800 GTS (G92)
tRD - 8.5, Memset Misreads The Value When Set Manually
Memory Speed - 1600MHZ, CPU-Z Misreports The Divider
Yellow Slots Used For Memory

click for larger image

click for larger image

Code:

CPU Feature Page
Thermal Management Control................Enabled
PPM (EIST) Mode...........................Disabled
Limit CPUID MaxVal........................Disabled
CIE Function..............................Disabled
Virtualization Technology.................Disabled
Core Multi-Processing.....................Enabled

Main BIOS Page
Exist Setup Shutdown......................Mode 2
Shutdown After AC Loss....................Disabled
O. C. Fail Retry Counter..................0
CLOCK VC0 Divider.........................Auto
CPU Clock Ratio...........................8.5x
CPU N/2 Ratio.............................Enabled
CPU Clock.................................480 MHz
Boot Up Clock.............................Auto
CPU Clock Amplitude.......................800mV
CPU Clock0 Skew...........................0ps
CPU Clock0 Skew...........................0ps
DRAM Speed................................400/1333
PCIE Clock................................100MHz
PCIE Slot Config..........................1X 1X

CPU Spread Spectrum.......................Disabled
PCIE Spread Spectrum......................Disabled
SATA Spread Spectrum......................Disabled

Voltage Setting Page 
CPU VID Control...........................1.34375V
CPU VID Special Add Limit.................Enabled
CPU VID Special Add.......................Auto
DRAM Voltage Control......................1.837V
SB Core/CPU PLL Voltage...................1.510V
NB Core Voltage...........................1.543V
CPU VTT Voltage...........................1.144V
VCore Droop Control.......................Disabled
Clockgen Voltage Control..................3.45V
GTL+ Buffers Strength.....................Strong
Host Slew Rate............................Weak
GTL REF Voltage Control...................Disabled
CPU GTL 1/2 REF Volt......................113
CPU GTL 0/3 REF Volt......................100
North Bridge GTL REF Volt ................100

DRAM Timing Page
Enhance Data Transmitting.................Fast
Enhance Addressing........................Fast
T2 Dispatch...............................Auto
Clock Setting Fine Delay..................Listed Below
CAS Latency Time (tCL)....................7
RAS# to CAS# Delay (tRCD).................6
RAS# Precharge (tRP)......................6
Precharge Delay (tRAS)....................20
All Precharge to Act......................Auto
REF to ACT Delay (tRFC)...................Auto
Performance Level.........................9
Read Delay Phase Adjust...................Listed Below
MCH ODT Latency...........................Auto
Write to PRE Delay (tWR)..................Auto
Rank Write to Read (tWTR).................Auto
ACT to ACT Delay (tRRD)...................Auto
Read to Write Delay (tRDWR)...............Auto
Ranks Write to Write (tWRWR)..............Auto
Ranks Read to Read (tRDRD)................Auto
Ranks Write to Read (tWRRD)...............Auto
Read CAS# Precharge (tRTP)................Auto
ALL PRE to Refresh........................Auto

Read Delay Phase Adjust Page
Channel 1 Phase 0 Pull-In.................Enabled
Channel 1 Phase 1 Pull-In.................Enabled
Channel 1 Phase 2 Pull-In.................Enabled
Channel 1 Phase 3 Pull-In.................Enabled
Channel 1 Phase 4 Pull-In.................Enabled

Channel 2 Phase 0 Pull-In.................Auto
Channel 2 Phase 1 Pull-In.................Auto
Channel 2 Phase 2 Pull-In.................Auto
Channel 2 Phase 3 Pull-In.................Auto
Channel 2 Phase 4 Pull-In.................Auto

Clock Setting Fine Delay Page
DRAM Default Skew Model...................Model 3

Fine Delay Step Degree....................5ps


Ch1 Clock Crossing Setting................Auto
DIMM 1 Clock fine delay...................Current 489ps
DIMM 2 Clock fine delay...................Current 489ps
DIMM 1 Control fine delay.................Current 434ps
DIMM 2 Control fine delay.................Current 473ps
Ch 1 Command fine delay...................Current 205ps

Ch2 Clock Crossing Setting................Auto
DIMM 3 Clock fine delay...................Current 686ps
DIMM 4 Clock fine delay...................Current 686ps
DIMM 3 Control fine delay.................Current 607ps
DIMM 4 Control fine delay.................Current 654ps
Ch 2 Command fine delay...................Current 182ps

Ch1Ch2 CommonClock Setting................Auto

Ch1 RDCAS GNT-Chip Delay..................Auto
Ch1 WRCAS GNT-Chip Delay..................Auto
Ch1 Command to CS Delay...................Auto

Ch2 RDCAS GNT-Chip Delay..................Auto
Ch2 WRCAS GNT-Chip Delay..................Auto
Ch2 Command to CS Delay...................Auto

Common CMD to CS Timing...................Auto

Praz · #**146** 21-06-2008, 20:33

XP SP3

click for larger image

click for larger image

3dx Max w/V-ray
Time to render: 14min 08sec

click for larger image

click for larger image

Praz · #**147** 21-06-2008, 20:34

Vista 64 Bit SP1

click for larger image

click for larger image

3dx Max w/V-ray
Time to render: 15min 30sec

click for larger image

click for larger image

Clunk · #**148** 21-06-2008, 20:43

Nice Praz, are you stuck around the same point as us? or can you go higher?

Praz · #**149** 21-06-2008, 20:49

Thanks. I've got a 2x2GB set of OCZ 1600EB sticks in now. Hope to have screenshots done soon at 500x8. Just trying to get a couple of board voltages down a bit. I've spent quite a bit of time with these and the Reapers finding common settings they both like at 1600MHz. Gonna give 8GB a shot next if they'll play well together.

Clunk · #**150** 21-06-2008, 20:54

Looking forward to the results, especially the 500FSB ones.