what kind of voltages are you running on mch/fsb/ram? seeing almost 1.4v on the cpu scares me!

ram is running at normal reference voltage of 1.95.
MCH +0.35
FSB +0.35

ok we are people we all make mistakesmy opinion about latest bioses for my system:
cpu:f6b-f6c-f6d-f6e all same cpu performance same o/c speed....

ram:f6b AND f6c(very good for o/c ram bioses 4sticks 6gb@1500mhz@6-5-5-10 trd=7 @+0.35v mem. volts from bios 1.85(1.88 real)

f6d AND f6e( unstable rams!i have to give +0.40 mem. volts(1.94) and to set trd=8)

so i stuck with f6C for now is the best for me for cpu and rams ... http://www.station-drivers.com/telec...x48tdq6f6c.exe

stable settings

Robust Graphics Booster...........:fast
CPU Clock Ratio...................:8
CPU Frequency.....................:3.60GHz(450x8)
CPU Host Clock Control............:Enabled
CPU Host Frequency(Mhz)...........:450MHz
PCI Express Frequency (Mhz).......:100MHz
C.I.A.2...........................isabled
Performance Enhance...............:Extreme
System Memory Multiplier (SPD)....:3.33D
Memory Frequency(Mhz).............:1500
DRAM Timing Selectable ...........:Manual
Standard Timing Control
CAS Latency Time (tCL)............:6
DRAM RAS# to CAS# (tRCD).........:5
DRAM RAS# Precharge (tRP).........:5
Precharge Delay (tRAS)............:10
Advanced Timing Control
ACT to ACT Delay(tRRD)............:[4]
Rank Write to READ Delay (tWTR)...:[4]
Write To Precharge Delay (tWR)....:[8]
Refresh to ACT Delay (tRFC).......:[60]
Read To Precharge Delay (tRTP)....:[4]
Static tREAD Value (tRD)..........:[7]
Static tREAD Phase Adj............: Auto
Command Rate (CMD)................: [2T]
Clock Driving and Skew Control
CPU/PCIEX Clock Driving Control...: 800mV
CPU Clock Skew Control............: 50ps
(G)MCH Clock Skew Control.........: 150ps
System Voltage Control () = Base Voltages
DDR3 OverVoltage Control...(1.50v): +0.35V
PCI-E OverVoltage Control.,(1.50v): +0.10V
FSB OverVoltage...................: +0.20
(G)MCH OverVoltage Control,(1.25v): +0.375
CPU GTLREF1 Voltage*.......(64%)..: Normal
CPU GTLREF2 Voltage*.......(67%)..: Normal
Loadline Calibration..............: Enabled
CPU Voltage Control...............: 1.3625V (effective on cpuz at full load: 1.312v)
Normal CPU Vcore..................: 1.23500V
Advanced Bios Features
Limit CPUID Max to 3..............: Disabled
No-Execute Memory Protect.........: Disabled
CPU Enhanced Halt(CIE)............: Disabled
CPU Thermal Monitor 2.............: Enabled
CPU EIST Function.................: Disabled
Virtualization Technology........: Disabled

yes I do remember having a lower trd (=6 i think) with f6c too...but f6d/e seemed to boot faster (newer raid bios i think?) so i stuck with f6e
i used to keep my cpu at about 3.9ghz, but keeping the voltage at the "maximum safe" value of 1.3625 was scaring me a bit, and my ram didn't seem to deal with it too well. much happier at 3.6 (400x9) and cpu-z reporting voltage of 1.230v. my fsb/mch are at +0.1/+0.15 and ram is running at much tighter timings with less volts too.

how much vdroop u have with 1.36250?i have 1.31 at load(0.05 vdroop) with loadline calibration enabled!if you have good cpu temps and u want to try more you can play with a +0.20 vtt and more mch volts i run at +0.375 24/7 but i addeda fan on it

i can't remember how the vdroop was when i was running at 3.9ish, it's been a while. right now my idle temp is 40-42 C with the fan set very low much rather have lower voltages/cooler temps/better ram timings than 300mhz.