Gigabyte GA X38 DQ6 Blog

[supershanks]

Hi ashura,
I'd try pushing your luck & ask specifically what width the mossfet block is , all the others are the same 15.5mm. If it's > say 14mm then they won't

Not used them yet, NB waterblock has been delayed & i'm busy early part of thisd week, so won't be able to try everything yet. However looking at the Enzotech Mosfet Heatsink - MOS-C1 They are excellent & i'm pretty confident that they'll fit in 2 rows over the PWM.

Hi Marcus,
Sorry can't help re bios i',m on the X48T at the minute.

luck

[ashura]

Alas, they're tight lipped:

As our HR-09 type4 is still under construction, I can only tell you this model will have less compatibility issue.

and after I asked when we can expect specs and compatibility:

Thank for your mail, as so far, we can not release any confirmed information for we are still on paper works.

Please pay attention to our website every one another day by day, we believe HR-09 type 4 will hit the market soon.


I don't have the patience for this, so those ezotech's it is.

[supershanks]

I don't have the patience for this, so those ezotech's it is.

says it all
In addition I got Enzotech SLF-1 to go on my Southbridge, the quality is great , will post pics when i get the NB block and get time to fit them all.

luck

[ckirkby3]

Hi i got the enzotech CNB-R1 for the northbridge, 2 packs of the mos-c1's (just to be on the safe side lol) for the mosfets, and the cnb s1l for the southbridge, hopefully it all fits.. hopefully get it all done tonight

[supershanks]

Fitted the Enzotech Mosfet Heatsink - MOS-C1 today 2 rows of 10. Takes a bit of time to mount them but looks good I've been able to mount 2x 40mm fans above them, i'm quite pleased with the,.

Sadly though the EnzoTech SLF-!doesnt fit the sb, where i had planned to put it.

I hope the CNB-R1 fits I measured the diagonal for the MB mounting points as 7.5cm.
Max shown on their website is 6.74cm

I'm currently running with a Thermalright HR-05-SLI on my NB , I can confirm that it fits

Will post some pics probably tomorrow. Also took pics of the nossfet cooler to send to thermalright.

luck

[ashura]

My Enzotech MOSFET coolers should be arriving today so I'll have pics of my install as well. The rest of the cooling will be a bit tricky to figure out because of the TRUE120, my gfx card and PCI-e devices, but I'm hoping to fit a HR05 SLI w/fan on the NB and a HR05 SLI fanless on the SB.

supershanks: as I'm not watercooling and have a fan exhausting from the TRUE leading straight to the case exhaust fan with the MOSFET right in between the two, I shouldn't need to worry about extra cooling for the MOS-C1 right?

[supershanks]

Bit of stuff on what I've fitted/fitting to replace the stock heatpipes.

Aftermarket Cooling X38/X48 1of3"

Aftermarket Cooling X38/X48 2of3"


Aftermarket Cooling X38/X48 3of3 NB Waterblock

[lokeey]

my current settings have so far yielded good results. here are my current settings

i've been stress testing (blend) for over 6 hrs without any issues. gonna let it ride for another 5-7 hours and then make some more tweaks since it's only a 5% overclock on the ram. gonna try for 1200 and then 1333 and see how that goes.

temps have been fairly low as well, too. the highest i've seen has been 62C.

whatcha think shanks?

[supershanks]

looking good m8

and then make some more tweaks since it's only a 5% overclock on the ram.

you might be able to reduce tRAS from 15 to 12 & TRFC to 35 on the 1120mem clock.

luck

[lokeey]

looking good m8
you might be able to reduce tRAS from 15 to 12 & TRFC to 35 on the 1120mem clock.

luck

damnit! spoke too soon...threads 1-3 went well for 8+ hours....got an error on #4 8 hrs 24 mins.

pic

i'll give your suggestions a try...thanks shanks!