DFI DK X58-T3eH6 Living Review

[supershanks]

Voltage Measuring Points
Couldn't be simpler, the same as it's more expensive big brother the DFI Lanparty UT X58-T3eH8 So another big plus for this board, the key measuring points you need in an easy access position.

If you don't know what you're doing, please DO NOT go poking around with a DMM, you will probably kill your board - Clunk.org.uk does not take any responsibility for any loss or damage as a result of using this information.

[supershanks]

Bios Template - DX58D123 BTA

PHP Code:

[code]
[u][B}DFI DK X58-T3eH6[/b][/U]
[B]Genie BIOS[/b]
[b]CPU Features Sub Menu[/b]
Set VR Current Limit Max.......: Disabled
Thermal Management Control.....: Disabled
EIST Function..................: Disabled
CxE Function...................: Disable
Execute Disable Bit............: Disabled
Virtualisation Technology......: Disabled
[U]***** Logical Processor Setting *****[/U]
Intel HT technology............: Enabled
Active Processor Cores.........: All

[b]DRAM Timing Sub Menu[/b]
Memory Control Setting.........:
Channel Interleave Setting.....:
Rank Interleave Setting........:
Memory LowGap..................: M
DRAM Command Rate..............: N
CAS Latency Time (tCL).........: 
RAS# to CAS# Delay (tRP).......: 
RAS# Precharge (tRP)...........: 
Precharge Delay (tRAS).........: 
REF to ACT Delay (tRFC)........: Auto
Write to Pre Delay (tWR).......: Auto
Rank Write to Read (tWTR)......: Auto
ACT to ACT Delay (tRRD)........: Auto
Row Cycle Time (tRC)...........: Auto
Read CAS# Precharge (tRTP).....: Auto
Four ACT WIN Time (tFAW).......: Auto

[b]Voltage Setting Sub Menu[/b]
O.C. Shut Down Free............: Enable
CPU VID Control................: v
Power Saving...................:[sTANDARD]  
Super VID......................:[oFF]
Vcore Auto PSI.................:
OCP............................:
DRAM Bus Voltage...............:
DRAM PWM Switch Frequency......: Nominal Frequency
DRAM PWM Phase Control.........: 2 Phase Operation
CPU VTT Special Add............: Auto
CPU VTT Voltage................: v
VTT PWM Switch Frequency.......: Nominal Frequency
VTT PWM Phase Control..........: 2 Phase Operation
CPU PLL Voltage................: v
IOH/ICH 1.1v Voltage...........: 1.10v
IOH Analog Voltage.............: 1.10v
ICH 1.5 Voltage................: 1.5v
ICH 1.05v Voltage..............: 1.05v
DIMM 1/2 DQ/DQSTB Bus VREF.....: %
DIMM 3/4 DQ/DQSTB Bus VREF.....: %
DIMM 5/6 DQ/DQSTB Bus VREF.....: %
DIMM 1/2 ADDR/CMD Bus VREF.....: %
DIMM 3/4 ADDR/CMD Bus VREF.....: %
DIMM 5/6 ADDR/CMD Bus VREF.....:%
CPU Core DQ/DQSTB Bus VREF.....: %
CPU QPI Drive Strength.........: Normal
IOH QPI Drive Strength.........: Normal

[b]Genie Main Mewnu(Contd)[/b]
Exit Setup Shut Down...........: Mode 2
O.C. Fail Retry Counter........: Enabled
O.C. Fail CMOS Reloaded........: Disabled
PPM Function...................: Enabled
Turbo Mode Function............: Disabled
x 1 Core Max Turbo Ratio ......: Enabled
x 2 Core Max Turbo Ratio.......: 21x
x 3 Core Max Turbo Ratio.......: 21x
x 4 Core Max Turbo Ratio.......: 21x

CPU Non-Turbo Clock Ratio......: 20x

[U]*BCLK/UCLK/QPI Controller Settings*[/U]

QPI Control Settings...........: Enabled
QPI Link Fast Mode.............: Enabled
QPI Frequency GT/Sec...........: 4.800GT/s (BCLK*18*2)
CPU Base Clock (BCLK)..........: 200MHz
Boot Up CPU Base Clock.........: Auto
PCIE Clock.....................: 100MHz
DRAM Frequency.................: BCLK*08 MHz
Uncore Frequency...............: BCLK*16 MHz

CPU Spread Spectrum............: Disabled
PCIE Spread Spectrum...........: Disabled
[/code] 


[roedzzz]

Another nice one's from DFI
Its have been arived yesterday.will test soon..
Nice work..And thanks for sharing bios setup and some information about this mobo mate

[supershanks]

Its have been arived yesterday.will test soon..

Nice one mate
Be nice to see how it goes for you & to have some company

[Clunk]

Desert Island discs

[supershanks]

Aye summat like that , glad at least I have leccy

[roedzzz]

Some result of mine





My highest BCLK 220*18..

CPU-Z Validator 3.0

[supershanks]

Very Nice mate
I'm just about to post my latest times I've gone similar way , but not with as higher BCLK yet 19x213 @x8 1704 8-8-8-22

[supershanks]

4,047Mhz 19x213 DDR3@x8 1,704Mhz 8-8-8-22
Vcore= 1.3625v , Vtt=1.40v VDimm=1.635v

Benches
Everest version below = 4.60.1639 Beta

Everest Version 1.5.1650


Stability
1 Hour OCCT Linpack


Bios Settings

Bios Settings
[B}DFI DK X58-T3eH6[/b]
Genie BIOS
CPU Features Sub Menu
Set VR Current Limit Max.......: Disabled
Thermal Management Control.....: Disabled
EIST Function..................: Disabled
CxE Function...................: Disable
Execute Disable Bit............: Disabled
Virtualisation Technology......: Disabled
***** Logical Processor Setting *****
Intel HT technology............: Enabled
Active Processor Cores.........: All

DRAM Timing Sub Menu
Memory Control Setting.........:Auto
Memory LowGap..................: 1792M upped from default for crossfire 4670
DRAM Command Rate..............:1N
CAS Latency Time (tCL).........:  8
RAS# to CAS# Delay (tRP).......: 8
RAS# Precharge (tRP)...........: 8
Precharge Delay (tRAS).........: 22
REF to ACT Delay (tRFC)........: 75
Write to Pre Delay (tWR).......: Auto
Rank Write to Read (tWTR)......: Auto
ACT to ACT Delay (tRRD)........: Auto
Row Cycle Time (tRC)...........: Auto
Read CAS# Precharge (tRTP).....: Auto
Four ACT WIN Time (tFAW).......: Auto

Voltage Setting Sub Menu
O.C. Shut Down Free............: Enable
CPU VID Control................: 1.3625v
Power Saving...................: STD
Super Vid.........................: OFF
Vcore Auto PSI.................: Disable
OCP............................:140A
DRAM Bus Voltage...............:1.635v
DRAM PWM Switch Frequency......: Nominal Frequency
DRAM PWM Phase Control.........: 2 Phase Operation
CPU VTT Special Add............: Auto
CPU VTT Voltage................: 1.40v
VTT PWM Switch Frequency.......: Nominal Frequency
VTT PWM Phase Control..........: 2 Phase Operation
CPU PLL Voltage................: 1.80v
IOH/ICH 1.1v Voltage...........: 1.10v
IOH Analog Voltage.............: 1.10v
ICH 1.5 Voltage................: 1.5v
ICH 1.05v Voltage..............: 1.05v
DIMM 1/2 DQ/DQSTB Bus VREF.....: 0 %
DIMM 3/4 DQ/DQSTB Bus VREF.....: 0%
DIMM 5/6 DQ/DQSTB Bus VREF.....: 0%
DIMM 1/2 ADDR/CMD Bus VREF.....: 0%
DIMM 3/4 ADDR/CMD Bus VREF.....: 0%
DIMM 5/6 ADDR/CMD Bus VREF.....: 0%
CPU Core DQ/DQSTB Bus VREF.....:  0%
CPU QPI Drive Strength.........: Normal
IOH QPI Drive Strength.........: Normal

Genie Main Menu(Cont'd)
Exit Setup Shut Down...........: Mode 2
O.C. Fail Retry Counter........: Enabled
O.C. Fail CMOS Reloaded........: Disabled
PPM Function...................: Enabled
Turbo Mode Function............: Enabled
x 1 Core Max Turbo Ratio ......: 22x
x 2 Core Max Turbo Ratio.......: 21x
x 3 Core Max Turbo Ratio.......: 21x
x 4 Core Max Turbo Ratio.......: 21x

CPU Non-Turbo Clock Ratio......: 19x

*BCLK/UCLK/QPI Controller Settings*

QPI Control Settings...........: Enabled
QPI Link Fast Mode.............: Enabled
QPI Frequency GT/Sec...........: Auto
CPU Base Clock (BCLK)..........: 213MHz
Boot Up CPU Base Clock.........: Auto
PCIE Clock.....................: 100MHz
DRAM Frequency.................:  x08
Uncore Frequency...............:  x16

CPU Spread Spectrum............: Disabled
PCIE Spread Spectrum...........: Disabled

[supershanks]

3.9Ghz 20x195 DDR3 x10 1,950Mhz 9-9-8-23 1.65v
Highest Memory clock so far, not quiet got to a bench able 2,000Mhz yet but this isn't a bad clock, just on the top end of the ram's voltage.


Benches

Note: Everest below is Version 4.60.1639 Beta shown for consistency with earlier benches.


Everest v5:-




Stability
CPU

Ram
Large FFTs:-


Bios Settings
initial values mat be able to tighten TRFC etc.,

[B}DFI DK X58-T3eH6[/b]
Genie BIOS
CPU Features Sub Menu
Set VR Current Limit Max.......: Disabled
Thermal Management Control.....: Disabled
EIST Function..................: Disabled
CxE Function...................: Disable
Execute Disable Bit............: Disabled
Virtualisation Technology......: Disabled
***** Logical Processor Setting *****
Intel HT technology............: Enabled
Active Processor Cores.........: All

DRAM Timing Sub Menu
Memory Control Setting.........: Auto
Channel Interleave Setting.....: 3 Way
Rank Interleave Setting........: Auto
Memory LowGap..................: 1536
DRAM Command Rate..............: 1N
CAS Latency Time (tCL).........: 9
RAS# to CAS# Delay (tRP).......: 9
RAS# Precharge (tRP)...........: 8
Precharge Delay (tRAS).........: 23
REF to ACT Delay (tRFC)........: 88
Write to Pre Delay (tWR).......: 10
Rank Write to Read (tWTR)......: 5
ACT to ACT Delay (tRRD)........: 4
Row Cycle Time (tRC)...........: 31
Read CAS# Precharge (tRTP).....: 5
Four ACT WIN Time (tFAW).......: 24

Voltage Setting Sub Menu
O.C. Shut Down Free............: Enable
CPU VID Control................: 1.3625v
Power Saving...................:[STANDARD]  
Super VID......................:[OFF]
Vcore Auto PSI.................: Disab
OCP............................: 140A
DRAM Bus Voltage...............: 1.65--> 1.665v for stability
DRAM PWM Switch Frequency......: Nominal Frequency
DRAM PWM Phase Control.........: 2 Phase Operation
CPU VTT Special Add............: Auto
CPU VTT Voltage................: 1.40v
VTT PWM Switch Frequency.......: Nominal Frequency
VTT PWM Phase Control..........: 2 Phase Operation
CPU PLL Voltage................: 1.80v
IOH/ICH 1.1v Voltage...........: 1.11v
IOH Analog Voltage.............: 1.10v
ICH 1.5 Voltage................: 1.5v
ICH 1.05v Voltage..............: 1.05v
DIMM 1/2 DQ/DQSTB Bus VREF.....: 0%
DIMM 3/4 DQ/DQSTB Bus VREF.....: 0%
DIMM 5/6 DQ/DQSTB Bus VREF.....: 0%
DIMM 1/2 ADDR/CMD Bus VREF.....: 0%
DIMM 3/4 ADDR/CMD Bus VREF.....: 0%
DIMM 5/6 ADDR/CMD Bus VREF.....: 0%
CPU Core DQ/DQSTB Bus VREF.....: 0%
CPU QPI Drive Strength.........: Normal
IOH QPI Drive Strength.........: Normal

Genie Main Mewnu(Cont'd)
Exit Setup Shut Down...........: Mode 2
O.C. Fail Retry Counter........: Enabled
O.C. Fail CMOS Reloaded........: Disabled
PPM Function...................: Enabled
Turbo Mode Function............: Disabled
x 1 Core Max Turbo Ratio ......: Enabled
x 2 Core Max Turbo Ratio.......: 22x
x 3 Core Max Turbo Ratio.......: 21x
x 4 Core Max Turbo Ratio.......: 21x

CPU Non-Turbo Clock Ratio......: 20x

*BCLK/UCLK/QPI Controller Settings*

QPI Control Settings...........: Enabled
QPI Link Fast Mode.............: Enabled
QPI Frequency GT/Sec...........: Auto
CPU Base Clock (BCLK)..........: 195MHz
Boot Up CPU Base Clock.........: Auto
PCIE Clock.....................: 100MHz
DRAM Frequency.................: x10 
Uncore Frequency...............: x20 

CPU Spread Spectrum............: Disabled
PCIE Spread Spectrum...........: Disabled