E4500 2.2ghz on Asus P5K - OC problem - Page 4

Clunk · #31 13-05-2009, 22:49

Give it some NB voltage.

SonOfaBeach · #32 13-05-2009, 23:28

Are u joking? Its not funny...

Clunk · #33 14-05-2009, 01:47

No. Try some NB voltage and see if it works.

Kelainefes · #34 14-05-2009, 03:56

Sometimes having 2x2GB sticks may require a slight increase in voltage on some motherboards/hardware configurations.

SonOfaBeach · #35 15-05-2009, 22:21

Hello Ladies

Finally i found out what was wrong with my wirless card. I had to install some extra drivers, cause my old were not able to work on PAE (it means physical added adress, or maybe something else ^^). So today i also installed my pretty pentagram cooler and i am very satisfited about it. Currently i am on new cooler and 4gb of ram.

Earlier, as u remember i wasnt even able to stable work on 3ghz, i got 75degrees after 30 second in orthos. Now its much MUCH better. Orthos runs 15 minutes (on 3 ghz) and temperatures dont cross over 63. OMG i am so happy

Thanks to the Kalainefes for very good bios configuration:

CPU Ratio setting: 9
FSB strap to NB: 333
FSB frequency: 333
DRAM Frequency: DDR2-800
CPU Voltage: 1.375
CPU PLL Voltage:1.5 (tops)
FSB Termination Voltage:1.3 (tops)

But if u want me to be honest, i expected something better :P I thought that i will get 3.4ghz or just 3.2.
I tried this bios conf:
CPU Ratio setting: 8
FSB strap to NB: 400
FSB frequency: 400
DRAM Frequency: DDR2-800
CPU Voltage: 1.4500 ( temperatures were fine, intel says that safe voltage for my cpu is 1.3 - 1.5)
CPU PLL Voltage:1.50
FSB Termination Voltage: 1.4
DRAM Voltage: 2.1

Windows starts normally but i cant even start orthos. Super pi doesnt make even 1 loop on 32M. What can I do?

Kelainefes · #36 16-05-2009, 00:51

Try going back to the 3GHz setup, but increase the multiplier to 10x which will give a CPU freq of 3.33 GHz.
It should be a "easier" OC compared to the 400x8 you tried, due to the lower FSB.
Increase vCore till stable, although I wouldn't go past 1.4 for 24/7 use.

SonOfaBeach · #37 16-05-2009, 02:14

My CPU is retarded. I am able to use it at 3Ghz with 1.3625v and orthos can run for 15 minutes and even longer.
But when i try what u just said on (attention) 1.4625 i can't let orthos go for not even 10 second cause it crashes. Is it possible that adding 0.1v doestn help to get 333mhz more? Same shit is on 320x10 on the same voltage. Oh wait, its better. Orthos runs for 10 seconds. (lol, thats a score)

WOW

Kelainefes · #38 16-05-2009, 06:27

Ok, you need to try and increase some other voltage, try upping the NB voltage a few steps. Also some FSB termination voltage may help.
Try one and then the other and then both together, see if you can find a good combination.
I'd say keep undeer a limit of 1.35 for the fsb termination and 1.45 for the NB.

SonOfaBeach · #39 16-05-2009, 13:13

I stay at 3Ghz and 1.3750v. I cant get anything better. Thank you anyway