quick ? about motherboard for q6600 ?

[stdu007]

so it's simple wich one of these 3 boards will give me a better oc result with a q6600 ... and please give some reasons why !!! thank's every one !!!

1-dfi lp ut p35 t2r
2-foxconn mars
3-abit ip35 pro

[Clunk]

I would think that the overclock would be limited by the CPU and cooling method more than any of those boards

I think the DFI and Abit would probably go highest overall though.

[stdu007]

so now i hit 367 fsb with my dfi board ... if i try 400x8 or x9 i can t boot ... even if i try to put more vcoore and all thing's with volt ... north south cpu vtt ... so what should i do to go further then 367 fsb ... im on water with 2 x mcr220 with dtex fusion block (cpu-gpu) ... so if you can help me it will be apreciated ...

[Clunk]

Make sure your RAM is set 1:1 333/667 strap maybe or 400/800. It sounds like your RAM is too high to start with.

[stdu007]

clunk ... my merory run at 1100mhz now with 367 fsb ... and when i try at 400 fsb it set at 1000 mhz ... so here my set up right now
e= enable and d= disable

Originally Posted by Clunk

PHP Code:

     DFI LP UT P35-T2R BIOS Template

CPU Feature
Thermal Management Control:d
PPM(EIST) Mode:d
Limit CPUID MaxVal:d
C1E Function:d
Execute Disable Bit:d
Virtualisation Technology:e
Core Multi-Processing:e

DRAM Timing
Enhanced Data Transmitting:fast
Enhanced Addressing:fast
T2 Dispatch:auto
*Clock Setting Fine Delay*
CH1 Clock Crossing Setting:agressive
DIMM 1 Clock Fine Delay:current
DIMM 2 Clock Fine Delay:current
CH1 Command Fine Delay:current
CH1 Control Fine Delay:current

CH2 Clock Crossing Setting:agressive
DIMM 3 Clock Fine Delay:current
DIMM 4 Clock Fine Delay:current
ch 2 Command Fine Delay:current
Ch 2 Control Fine Delay:current

Ch1CH2 CommonClock Setting:auto

Ch1 RDCAS GNT-Chip Delay:auto
Ch1 WRCAS GNT-Chip Delay:auto
Ch1 Command to CS Delay:auto

Ch2 RDCAS GNT-Chip Delay:auto
Ch2 WRCAS GNT-Chip Delay:auto
Ch2 Command to CS Delay:auto

CAS Latency Time (tCL):5
RAS# to CAS# Delay (tRCD):4
RAS# Precharge (tRP):4
Precharge Delay (tRAS):12
All Precharge to Act:auto
REF to ACT Delay (tRFC):auto
Performance LVL (Read Delay):auto
Read Delay Phase Adjust:auto
*Ch1 Read Delay Phase (4~0)*
Channel 1 Phase 0 Pull-In:auto
Channel 1 Phase 1 Pull-In:auto
Channel 1 Phase 2 Pull-In:auto
Channel 1 Phase 3 Pull-In:auto
Channel 1 Phase 4 Pull-In:auto

*Ch2 Read Delay Phase (4~0)*

Channel 2 Phase 0 Pull-In:auto
Channel 2 Phase 1 Pull-In:auto
Channel 2 Phase 2 Pull-In:auto
Channel 2 Phase 3 Pull-In:auto
Channel 2 Phase 4 Pull-In:auto

MCH ODT Latency:
Write to Pre Delay (tWR):auto
Rank Write to Read (tWTR):auto
ACT to ACT Delay (tRRD):auto
Read to Write Delay (tRDWR):auto
Ranks Write to Write (tWRWR):auto
Ranks Read to Read (tRDRD):auto
Ranks Write to Read (tWRRD):auto
Read CAS# Precharge (tRTP):auto
All PRE to Refresh:auto

Voltage Setting.
CPU VID Control:1.48
CPU VID Special Add:100.23
DRAM Voltage Control:2.31
SB 1.05V Voltage:1.07
NB Core/CPU PLL Voltage:1.55
CPU VTT Voltage:1.45
Vcore Droop Control:e
Clockgen Voltage Control:3.45
GTL+ Buffers Strength:strong
Host Slew Rate:weak
GTL REF Voltage Control: - disabled ->
CPU GTL 1/3 REF Volt:auto
CPU GTL 0/2 REF Volt:auto
North Bridge GTL REF Volt:auto

Exit Setup Shutdown:mode2
Shutdown After AC Loss:d
Clock VCO Divider:auto
Clock CPU Ratio:9
*Target CPU Clock*
CPU Clock:367
Boot Up Clock:auto
DRAM Speed:266/667
*Target DRAM Speed*
PCIE Clock:105
PCIE Slot Config:1x 1x

CPU Spread Spectrum:d
PCIE Spread Spectrum:d
SATA Spread Spectrum:d 


[Clunk]

OK, that's the problem. Set the memory strap lower so the RAM is double the speed of the FSB 367/734 etc

[stdu007]

ok so this way i should be able to run my cpu over 400 fsb that it ... i will try tomorrow and let you know ... thank's for the help ...

[Clunk]

Yes, you should be ok if you do it like that

[stdu007]

c1 error ... need to erase the bios ... no succes ... so i think i will need to put some more juice to the cpu !!!

[Kidda!]

Originally Posted by stdu007

c1 error ... need to erase the bios ... no succes ... so i think i will need to put some more juice to the cpu !!!

nooooooooo ......

i have the dfi P35 and your pissing against the wind there matey
as Clunk pointed out you have overclocked your Ram
Clear Cmos and start again using the 1:1 ratio
looking at your cpu volts in the screenies for 3.3ghz you've either got an exceptionally bad G0 chip or you are way overvolting for the overclock.

Set you ram speeds to whats quoted on the box ...... go for a 1:1 ratio and try a 3ghz overclock ? leave the rest in auto , if it fails again for me i'd try memtest on the ram