Overclocking Templates / BIOS Templates - Page 3

steve_sarge · #21 08-09-2008, 12:49

PHP Code:


			
[code]
[b]DFI UT X48-T3RS LanParty[/b]
[b]CPU Feature[/b]
- Thermal Management Control: Disabled
- PPM(EIST) Mode: Disabled
- Limit CPUID MaxVal: Disabled
- CIE Function: Disabled
- Execute Disable Bit: Disabled
- Virtualization Technology: Disabled
- Core Multi-Processing: Enabled

Exist Setup Shutdown: Mode 2
Shutdown after AC Loss: Disabled
O.C. Fail retry Counter: 0
CPU Clock Ratio: 9x
CPU N/2 ratio: Disabled
Target CPU Clock: 3600MHz
CPU Clock: 400MHz
Boot Up Clock: Auto
CPU Clock Amplitude: 800mV
CPU Clock0 Skew: 0ps
CPU Clock1 Skew: 0ps
DRAM Speed: 400/1333
Target DRAM Speed:DDR3 1333
PCIE Clock: 100mhz
PCIE Slot Config: 1X 1X

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

[b]Voltage Settings[/b]
CPU VID Control: Auto 1.2200V
CPU VID Special Add Limit: Enabled
CPU VID Special Add: Auto
DRAM Voltage Control: 1.510V
SB Core/CPU PLL Voltage: 1.510V
NB Core Voltage: 1.291V
CPU VTT Voltage: 1.100V
Vcore Droop Control: Enabled
Clockgen Voltage Control: 3.45v
GTL+ Buffers Strength: Strong
Host Slew Rate: Weak
x MCH RON Offset Value: 00
x MCH RTT   Offset Value: 00
x MCH Slew Rate Offset Value: 00
x MCH VREF 1 Value
x MCH VREF 2 Value
x MCH VREF 3 Value
GTL REF Voltage Control: Disable
x CPU GTL1/3 REF Volt: 113
x CPU GTL 0/2 REF Volt: 100
x North Bridge GTL REF Volt: 100

 CPU Core Voltage: 1.20V
 DRAM      Voltage: 1.50V
 NB Core   Voltage: 1.32V
 CPU VTT  Voltage: 1.10V

[b]DRAM Timing[/b]
- Enhance Data transmitting: AUTO
- Enhance Addressing: AUTO
- T2 Dispatch: Auto

[b]Clock Setting Fine Delay: Press Enter[/b]

CAS Latency Time (tCL): 9
RAS# to CAS# Delay (tRCD): 9
RAS# Precharge (tRP): 9
Precharge Delay (tRAS): 24
All Precharge to Act: AUTO
REF to ACT Delay (tRFC): AUTO
Performance LVL (Read Delay): AUTO
Read delay phase adjust: Press Enter
MCH ODT Latency: AUTO
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Read to Write Delay (tRDWR): AUTO
Ranks Write to Write (tWRWR): AUTO
Ranks Read to Read (tRDRD): AUTO
Ranks Write to Read (tWRRD): AUTO
Read CAS# Precharge (tRTP): AUTO
ALL PRE to Refresh: AUTO 

DRAM CLK Driving Strength: Level 6
DRAM Data Driving Strength: Level 8
Ch1 DLL Default Skew Model: Model 0
Ch2 DLL Default Skew Model: Model 0

Fine Delay Step Degree: 5ps

Ch1 Clock Crossing Setting: AUTO
- DIMM 1 Clock fine delay: Current 489ps
- DIMM 2 Clock fine delay: Current 489ps
- DIMM 2 Control Fine Delay: Current 434ps
- DIMM 1 Control Fine Delay: Current 473ps
- Ch 1 Command fine delay: Current 560ps

Ch2 Clock Crossing Setting: AUTO
- DIMM 3 Clock fine delay: Current 686ps
- DIMM 4 Clock fine delay: Current 686ps
- DIMM 4 Control Fine Delay: Current 607ps
- DIMM 3 Control Fine Delay: Current 654ps
- Ch 2 Command fine delay: Current 693ps

Ch1Ch2 CommonClock Setting: Auto

Ch1 RDCAS GNT-Chip Delay: Auto
Ch1 WRCAS GNT-Chip Delay: Auto
Ch1 Command to CS Delay: Auto

Ch2 RDCAS GNT-Chip Delay: Auto
Ch2 WRCAS GNT-Chip Delay: Auto
Ch2 Command to CS Delay: Auto 

Common CMD to CS Delay: Auto
[/code]

I have taken the DFI LP UT P35-T2R Template from Clunk's post and modified it to the photos I took from my BIOS (My settings are entered in this post and I can't remember the ones that are stock) The RAM timings were Auto, the RAM strap was Auto, the FSB was auto too I think and the CPU controls were all enabled prior to my input, from memory. I do hope this will be helpful to others looking for a template fortheir board. I don't know how to post it as php, so if you guys think it's good enough, you may wish to php it.

supershanks · #22 08-09-2008, 21:32

Hi Steve thanks a lot mate

have added the php bit & added your template to index

steve_sarge · #23 09-09-2008, 02:34

No Probs Supershanks. It's about time I tried to give a little back as I have used your forum for quite a bit of research and info.

supershanks · #24 09-09-2008, 09:42

Quote:

It's about time I tried to give a little back as I have used your forum for quite a bit of research and info.

that's what we're here for.

Thanks

aavikkokettu · #25 26-09-2008, 15:31

Code:

Extreme Tweaker
Ai Overclock Tuner : Manual
OC From CPU Level Up : AUTO
Ratio CMOS Setting : AUTO
FSB Frequency :
CPU Clock Skew : AUTO
NB Clock Skew : AUTO 
FSB Strap to North Bridge : AUTO
DRAM Frequency: 
DRAM CLK Skew On Channel A1: AUTO
DRAM CLK Skew On Channel A2: AUTO
DRAM CLK Skew On Channel B1: AUTO
DRAM CLK Skew On Channel B2: AUTO
DRAM Timing Control: Manual

CAS# Latency : 
RAS# to CAS# Delay : 
RAS# Precharge : 
RAS# Activate to Precha : 
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time : AUTO
Write Recovery Time : AUTO
Read to Precharge Time : AUTO

Read to Write Delay (S/D) : AUTO
Write to Read Delay (S) : AUTO
Write to Read Delay (D) : AUTO
Read to Read Delay (S) : AUTO
Read to Read Delay (D) : AUTO
Write to Write Delay (S) : AUTO
Write to Write Delay (D) : AUTO

Write to Pre Delay : Auto
Read to Pre Delay : Auto
Pre to Pre Delay : Auto
All Pre to act Delay : Auto
All Pre to Ref Delay : Auto

DRAM Static Read Control: Disabled
Dram Read Training : Auto
Mem. OC Charger : Auto
Ai Clock Twister : AUTO
Transaction Booster : AUTO
PCIE Freguency : 100

CPU Voltage : 
CPU PLL Voltage : 
FSB Termination Voltage : 
DRAM Voltage : 
North Bridge Voltage : 
South Bridge 1.5 Voltage : AUTO
South Bridge 1.1 Voltage : AUTO

CPU GTL Reference (0) : 
CPU GTL Reference (1) :
CPU GTL Reference (2) :
CPU GTL Reference (3) :
NB GTL Reference : AUTO
DDR2 ChA Reference Voltage : 
DDR2 ChB Reference Voltage : 
North Bridge DDR Reference :

CPU Configuration
Ratio CMOS Setting : 
C1E Suppport : Disabled
Max CPUID Value Limit : Disabled
Intel (R) Virtualization Tech. :
CPU Disable Bit :  
Execute Disable Bit : Disabled
Intel (R) Speed Step (tm) Tech : 

Load-Line Calibration : 
CPU Spread Spectrum : Disabled
PCIE Spread Spectrum : Disabled

-----------------------------------
I hope those are all right with out typos

There is few blank point because im not shore whats they should be.

Clunk · #26 26-09-2008, 16:27

Thanks for that mate

supershanks · #27 26-09-2008, 18:56

tanks added to index post #1

Clunk · #28 14-10-2008, 04:38

DFI JR P45-T2RS BIOS Template

CPU Feature:
Thermal Management Control: Disabled
PPM (EIST) Mode: Disabled
Limit CPUID MaxVal: Disabled
C1E Function: Disabled
Execute Disable Bit: Disabled
Virtualization Technology: Disabled
Core Multi-Processing: Enabled

DRAM Timing:
CAS Latency Time (tCL) 5
RAS# to CAS# Delay (tRCD) 5
RAS# Precharge (tRP) 5
Precharge Delay (tRAS) 15
All Precharge to Act AUTO
REF to ACT Delay (tRFC) AUTO
Write to PRE Delay (tWR) AUTO
Rank Write to Read (tWTR) AUTO
ACT to ACT Delay (tRRD) AUTO
Read CAS# Precharge (tRTP) AUTO
Read CAS# Precharge (tRTP) AUTO
All PRE to Refresh AUTO

Voltage Setting:
CPU VID Special Add: +87.5mV
DRAM Voltage Control: 2.194
SB Core/CPU PLL Voltage: 1.55v
NB Core Voltage: 1.10v
Clockgen Voltage Control: 3.45v
CPU GTL 0/2 REF Volt: 0.67X
CPU GTL 1/3 REF Volt: 0.67X
North Bridge GTL REF Volt: 0.67X
FSB Vref: AUTO

AC Shutdown Free: Enabled
O.C. Fail Retry Counter: 1
O.C. Fail CMOS Reload: Disabled
CPU Clock Ratio: 10X
CPU N/2 Ratio: Disabled
Target CPU Clock: 3600MHz
CPU Clock: 360 MHz
DRAM Speed: 333/667
Target DRAM Speed: DDR2 721
PCIE Clock: 100MHz

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

Clunk · #29 09-12-2008, 16:10

BIOS Template - Gigabyte GA-EX58 - EXTREME MB Intelligent Tweaker (M.I.T.)

CPU Clock Ratio [20x]

Advanced CPU Features [Press Enter]:
CPU Clock Ratio [20x]
Intel(R) Turbo Boost Tech [Enabled]
CPU Cores Enabled [All]
CPU Multi Threading [Enabled]
CPU Enhanced Halt (C1E) [Enabled]
C3/C6/C7 State Support [Disabled]
CPU Thermal Monitor [Enabled]
CPU EIST Function [Enabled]
Virtualization Technology [Enabled]
Bi-Directional PROCHOT [Enabled]

QPI Link Speed [AUTO]

Uncore & QPI Features [Press Enter]:
QPI Link Speed [AUTO]
Uncore Frequency [AUTO]
Isonchronous Frequency [Enabled]

Base Clock (BCLK) Control [Enabled]
BCLK Frequency (MHz) [160]

Advanced Clock Control [Press Enter]:
standard clock control
Base Clock (BCLK) Control [Enabled]
BCLK Frequency (MHz) [160]
PCI Express Frequency (MHz) [AUTO]
C.I.A.2 [Disabled]

advanced clock control
CPU Clock Drive [ 700mV]
PCI Express Clock Drive [ 700mV]
CPU Clock Skew [ 0ps]
IOH Clock Skew [ 0ps]

Performance Enhance [Turbo]
Extreme Memory Profile (X.M.P.) [Disabled]
System Memory Multiplier (SPD) [AUTO]
DRAM Timing Selectable (sPD) [Manual]

Channel A

CAS Latency Time 8 [AUTO]
tRCD 8 [AUTO]
tRP 8 [AUTO]
tRAS 20 [AUTO]

Channel B

CAS Latency Time 8 [AUTO]
tRCD 8 [AUTO]
tRP 8 [AUTO]
tRAS 20 [AUTO]

Channel C

CAS Latency Time 8 [AUTO]
tRCD 8 [AUTO]
tRP 8 [AUTO]
tRAS 20 [AUTO]

Advanced DRAM Features [Press Enter]:
Performance Enhance [Turbo]
Extreme Memory Profile (X.M.P) [Disabled]
System Memory Multiplier (SPD) [AUTO]
DRAM Timing Selectable (sPD) [Manual]

Channel A

Channel A Timing Settings [Press Enter]:
##Channel A Standard Timing Control##
CAS Latency Time 8 [AUTO]
tRCD 8 [AUTO]
tRP 8 [AUTO]
tRAS 20 [AUTO]

##Channel A Advanced Timing Control##
tRC 27 [AUTO]
tRRD 4 [AUTO]
tWTR 4 [AUTO]
tWR 8 [AUTO]
tRFC 60 [AUTO]
tRTP 4 [AUTO]
tFAW 20 [AUTO]
Command Rate (CMD) 1 [AUTO]

##Channel A Misc Timing Control##
Round Trip Latency 58 [AUTO]

Channel A Turnaround Settings [Press Enter]:
##Channel A Writes Followed By Reads##
Different DIMMs 6 [AUTO]
Different Ranks 6 [AUTO]
On The Same Rank 6 [AUTO]

##Channel A Reads Followed By Writes##
Different DIMMs 8 [AUTO]
Different Ranks 8 [AUTO]
On The Same Rank 8 [AUTO]

##Channel A Reads Followed By Reads##
Different DIMMs 6 [AUTO]
Different Ranks 5 [AUTO]
On The Same Rank 1 [AUTO]

##Channel A Writes Followed By Writes##
Different DIMMs 6 [AUTO]
Different Ranks 6 [AUTO]
On The Same Rank 1 [AUTO]

Channel B

Channel B Timing Settings [Press Enter]:
##Channel B Standard Timing Control##
CAS Latency Time 8 [AUTO]
tRCD 8 [AUTO]
tRP 8 [AUTO]
tRAS 20 [AUTO]

##Channel B Advanced Timing Control##
tRC 27 [AUTO]
tRRD 4 [AUTO]
tWTR 4 [AUTO]
tWR 8 [AUTO]
tRFC 60 [AUTO]
tRTP 4 [AUTO]
tFAW 20 [AUTO]
Command Rate (CMD) 1 [AUTO]

##Channel B Misc Timing Control##
Round Trip Latency 58 [AUTO]

Channel A Turnaround Settings [Press Enter]:
##Channel B Writes Followed By Reads##
Different DIMMs 6 [AUTO]
Different Ranks 6 [AUTO]
On The Same Rank 6 [AUTO]

##Channel B Reads Followed By Writes##
Different DIMMs 8 [AUTO]
Different Ranks 8 [AUTO]
On The Same Rank 8 [AUTO]

##Channel B Reads Followed By Reads##
Different DIMMs 6 [AUTO]
Different Ranks 5 [AUTO]
On The Same Rank 1 [AUTO]

##Channel B Writes Followed By Writes##
Different DIMMs 6 [AUTO]
Different Ranks 6 [AUTO]
On The Same Rank 1 [AUTO]

Channel C

Channel C Timing Settings [Press Enter]:
##Channel C Standard Timing Control##
CAS Latency Time 8 [AUTO]
tRCD 8 [AUTO]
tRP 8 [AUTO]
tRAS 20 [AUTO]

##Channel C Advanced Timing Control##
tRC 27 [AUTO]
tRRD 4 [AUTO]
tWTR 4 [AUTO]
tWR 8 [AUTO]
tRFC 60 [AUTO]
tRTP 4 [AUTO]
tFAW 20 [AUTO]
Command Rate (CMD) 1 [AUTO]

##Channel C Misc Timing Control##
Round Trip Latency 58 [AUTO]

Channel C Turnaround Settings [Press Enter]:
##Channel C Writes Followed By Reads##
Different DIMMs 6 [AUTO]
Different Ranks 6 [AUTO]
On The Same Rank 6 [AUTO]

##Channel C Reads Followed By Writes##
Different DIMMs 8 [AUTO]
Different Ranks 8 [AUTO]
On The Same Rank 8 [AUTO]

##Channel C Reads Followed By Reads##
Different DIMMs 6 [AUTO]
Different Ranks 5 [AUTO]
On The Same Rank 1 [AUTO]

##Channel C Writes Followed By Writes##
Different DIMMs 6 [AUTO]
Different Ranks 6 [AUTO]
On The Same Rank 1 [AUTO]

Load Line Calibration [Disabled]
CPU Vcore 1.29375v [AUTO]
QPI/VTT Voltage 1.150v [AUTO]
IOH Core 1.100v [AUTO]
DRAM Voltage 1.5v [AUTO]

Advanced Voltage Control [Press Enter]:
Load Line Calibration [Disabled]
CPU Vcore 1.29375v [AUTO]
QPI/VTT Voltage 1.150v [AUTO]
CPU PLL 1.800v [AUTO]

MCH

PCIE 1.500v [AUTO]
QPI PLL 1.100v [AUTO]
IOH Core 1.100v [AUTO]
ICH I/O 1.500v [AUTO]
ICH Core 1.1v [AUTO]

DRAM

DRAM Voltage 1.500v [AUTO]
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]
Ch-C Address VRef. 0.750v [AUTO]

Clunk · #30 19-01-2009, 20:33

DFI UT 58-T3eH8 BIOS Template.

This should be good for 4GHz on a 920 too, give or take a bit of Vcore.

HTML Code:

CPU Feature:
Set VR Current Limit Max: Disabled
Thermal Management Control: Disabled
EIST Function: Disabled
CxE Function: Disable
Execute Disable Bit: Disabled
Virtualisation Technology: Disabled

*****  Logical Processor Setting  *****

Intel HT technology: Enabled
Active Processor Cores: All

DRAM Timing:
Memory Control Setting: Auto
Memory LowGap: 1536M

DRAM Command Rate: 1N
CAS Latency Time (tCL): 8
RAS# to CAS# Delay (tRP): 8
RAS# Precharge (tRP): 8
Precharge Delay (tRAS): 24
REF to ACT Delay (tRFC): Auto
Write to Pre Delay (tWR): Auto
Rank Write to Read (tWTR): Auto
ACT to ACT Delay (tRRD): Auto
Row Cycle Time (tRC): Auto
Read CAS# Precharge (tRTP): Auto
Four ACT WIN Time (tFAW): Auto

Voltage Setting:
O.C. Shut Down Free: Enable
CPU VID Control: 1.42500v
CPU VID Special Add Limit: Enabled
CPU VID Speciall Add: Auto
Vcore Droop Control: Enabled
DRAM Bus Voltage: 1.650v
DRAM PWM Switch Frequency: Nominal Frequency
DRAM PWM Phase Control: 2 Phase Operation
CPU VTT Special Add: Auto
CPU VTT Voltage: 1.48v
VTT PWM Switch Frequency: Nominal Frequency
VTT PWM Phase Control: 2 Phase Operation
CPU PLL Voltage: 1.80v
IOH/ICH 1.1v Voltage: 1.10v
IOH Analog Voltage: 1.10v
ICH 1.5 Voltage: 1.5v
ICH 1.05v Voltage: 1.05v
DIMM 1/2 DQ/DQSTB Bus VREF: -00.0%
DIMM 3/4 DQ/DQSTB Bus VREF: -00.0%
DIMM 5/6 DQ/DQSTB Bus VREF: -00.0%
ADDR/CMD VREF Control: Disable
x DIMM 1/2 ADDR/CMD Bus VREF 110
x DIMM 3/4 ADDR/CMD Bus VREF 110
x DIMM 5/6 ADDR/CMD Bus VREF 110

CPU QPI Drive Strength: Normal
IOH QPI Drive Strength: Normal

Exit Setup Shut Down: Mode 2
O.C. Fail Retry Counter: Enabled
O.C. Fail CMOS Reloaded: Disabled

PPM Function: Enabled
Turbo Mode Function: Disabled
x 1 Core Max Turbo Ratio 22x
x 2 Core Max Turbo Ratio 21x
x 3 Core Max Turbo Ratio 21x
x 4 Core Max Turbo Ratio 21x

CPU Non-Turbo Clock Ratio: 20x

*  BCLK/UCLK/QPI Controller Settings  *
 
QPI Control Settings: Enabled
QPI Link Fast Mode: Enabled
QPI Frequency: 4.800GT/s (BCLK*18*2)
CPU Base Clock (BCLK): 200MHz
Boot Up CPU Base Clock: Auto
PCIE Clock: 100MHz
DRAM Frequency: BCLK*08 MHz
Uncore Frequency: BCLK*16 MHz

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled