Overclocking Templates / BIOS Templates

[supershanks]

[b]DFI LT X38-T2R LanParty[/b]
[b]CPU Feature[/b]
- Thermal Management Control: Disabled
- PPM(EIST) Mode: Disabled
- Limit CPUID MaxVal: Disabled
- CIE Function: Disabled
- Execute Disable Bit: Disabled
- Virtualization Technology: Disabled
- Core Multi-Processing: Enabled

Exist Setup Shutdown: Mode 2
Shutdown after AC Loss: Disabled
CLOCK VC0 divider: AUTO
CPU Clock Ratio Unlock: Enabled
CPU Clock Ratio:
Target CPU Clock:
CPU Clock:
Boot Up Clock:
DRAM Speed:
Target DRAM Speed:
PCIE Clock: 100mhz
PCIE Slot Config: 1X 1X

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
SATA Spread Spectrum: Disabled

[b]Voltage Settings[/b]
CPU VID Control:
CPU VID Special Add:
DRAM Voltage Control:
SB Core/CPU PLL Voltage:
NB Core Voltage:
CPU VTT Voltage:
Vcore Droop Control: Enabled
Clockgen Voltage Control: 3.45v
GTL+ Buffers Strength: Strong
Host Slew Rate: Weak
GTL REF Voltage Control: Disable
x CPU GTL1/3 REF Volt: 110
x CPU GTL 0/2 REF Volt: 110
x North Bridge GTL REF Volt: 110

[b]DRAM Timing[/b]
- Enhance Data transmitting: AUTO
- Enhance Addressing: AUTO
- T2 Dispatch: Disabled

[b]Clock Setting Fine Delay[/b]
Ch1 Clock Crossing Setting: AUTO
- DIMM 1 Clock fine delay: Current
- DIMM 2 Clock fine delay: Current
- Ch 1 Command fine delay: Current
- Ch 1 Control fine delay: Current


Ch2 Clock Crossing Setting: AUTO
- DIMM 3 Clock fine delay: Current
- DIMM 4 Clock fine delay: Current
- Ch 2 Command fine delay: Current
- Ch 2 Control fine delay: Current

Ch1Ch2 CommonClock Setting: Auto

Ch1 RDCAS GNT-Chip Delay: Auto
Ch1 WRCAS GNT-Chip Delay: Auto
Ch1 Command to CS Delay: Auto

Ch2 RDCAS GNT-Chip Delay: Auto
Ch2 WRCAS GNT-Chip Delay: Auto
Ch2 Command to CS Delay: Auto 

CAS Latency Time (tCL):
RAS# to CAS# Delay (tRCD):
RAS# Precharge (tRP):
Precharge Delay (tRAS):
All Precharge to Act: AUTO
REF to ACT Delay (tRFC): AUTO
Performance LVL (Read Delay) (tRD): AUTO

Read delay phase adjust: Enter

Ch1 Read delay phase (4~0)
- Channel 1 Phase 0 Pull-In: Auto
- Channel 1 Phase 1 Pull-In: Auto
- Channel 1 Phase 2 Pull-In: Auto
- Channel 1 Phase 3 Pull-In: Auto
- Channel 1 Phase 4 Pull-In: Auto

Ch2 Read delay phase (4~0)
- Channel 2 Phase 0 Pull-In: Auto
- Channel 2 Phase 1 Pull-In: Auto
- Channel 2 Phase 2 Pull-In: Auto
- Channel 2 Phase 3 Pull-In: Auto
- Channel 2 Phase 4 Pull-In: Auto

MCH ODT Latency: AUTO
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Read to Write Delay (tRDWR): AUTO
Ranks Write to Write (tWRWR): AUTO
Ranks Read to Read (tRDRD): AUTO
Ranks Write to Read (tWRRD): AUTO
Read CAS# Precharge (tRTP): AUTO
ALL PRE to Refresh: AUTO 

[supershanks]

[B][U]Foxconn Mars[/U][/B]    

[B][U]Gladiator BIOS    [/U][/B]
[B][I]CPU Features - Sub Menu    [/I][/B]
EIST Function.........................Disabled
Limit CPUID MaxVal...................Disabled
C1E Function...........................Disabled
Execute Disable Bit...................Disabled
Virtualization Technology...........Disabled
Frequency Unlimit.....................Disabled
Core Multi Proceessing..............Enabled
[B][I]Memory Timing Config - Sub Menu    [/I][/B]
Dram Timing Selectable    
Cas  Latency Time (tCL).............    
Ras# to Cas# Delay (tRCD).........    
Ras# Precharge (tRP)................    
Precharge delay (tRAS)..............    
Write to Precharge (tWR)...........    
Row Refresh Cycle (tRFC)...........    
Write to Read Delay (tWTR)........    
Row to Row Delay (tRRD)    ..........
Read to Precharge (tRTP)...........    
Fast Chip Select.......................    
Clock Per Command...................    
Memory Channel0 DLL Adjust.......    
Memory Channel1 DLL Adjust.......    
Refresh Count Adjust.................    
Performance Level....................    
[B][I]All Voltage Control -Sub Menu    [/I][/B]
CPU Voltage Multiplier............... v
CPU Voltage Setting..................v    
Target CPU Voltage...................v    
Dram Voltage Setting.................v    
NB Voltage Setting....................v    
CPU VTT Voltage Setting    ...........v
SB Voltage Setting....................v    
    
Overclock Phase Select    Manual O.C.
CPU Clock Ratio Unlock...............
CPU Clock Ratio    ....................... Mhz
CPU N/2 Ratio..........................
Target CPU Core Speed.............
CPU Clock............................... Mhz
CPU Clock v Memory Speed.......    
System Memory Speed............      Mhz
PCI Express Clock...................  Mhz
PCI Clock..............................33.33 Mhz
    
Auto Detect PCI Clock    Enabled
Spread Spectrum    Disabled
Over Clock Recovery    Enabled 

[supershanks]

[B][U]Asus P5E3 Deluxe Wifi[/U][/B][U][/U]

[B]Configure advanced CPU settings[/B]
CPU Ratio Control............:
  Ratio to CMOS Setting......:
C1E Support..................:
CPU TM Function..............:
Vanderpool Technology........:
Execute Disable Bit..........:
Max CPUID Value Limit........:
Intel Speedstep EIST.........:

[U][B]AI Tweaker[/B][/U]
[B]Comfigure System Performance Settings[/B]

Ai OVerclocking Tuner........: [Manual]
CPU Ratio Control............: 
CPU Ratio Setting............:
FSB Strap to North Bridge....: 
FSB Frequency................: 
PCIE Frequency...............: 
DRAM Frequency...............: 
DRAM Command Rate............:
Dram TIming COntrol......... : [Manual]
[B]Pri. Information[/B]......: - - - - - - -
CAS# Latency.................:
RAS# to CAS #Delay...........:
RAS# Pre Time................:
RAS# Active Time.............:
RAS# to RAS# Delay...........:
Row Refresh Cycle Time.......:
Write Recovery Time..........:
Read to Precharge Time.......:
[B]Sec. Information[/B]......: - - - - - - 
Read to Write Delay (S/D)....:
Write to Read Delay (S)......:
Write to Read Delay (D)......: 
Read to Read Delay (S).......:
Read to Read Delay (D).......: 
Write to Write Delay (S).....: 
Write to Write Delay (D).....:
DRAM Static Read Control.....: 
DRAM Dynamic Write Control...: 

Ai Clock Twister.............:
Ai Clock Skew for Channel.A..:
Ai Clock Skew for Channel.B..:
Ai Transaction Booster.......: 

CPU Voltage..................:
CPU PLL Voltage..............:
FSB Termination Voltage......:
DRAM Voltage.................:
North Bridge Voltage.........:
South Bridge Voltage.........:
Clock Over-Charging Voltage..:

Load-Line Calibration........:
CPU GTL Voltage Reference....:
NB GTL Voltage Referemce.....:
CPU Spread Spectrum..........: [Disabled]
PCIE Spread Spectrum.........: [Disabled} 

[supershanks]

[B][U]GIGABYTE GA X48T DQ6 Clock Settings[/U][/B]

[B][U]MB Intelligent Tweaker (MIT)[/U][/B]
Robust Graphics Booster...........:
CPU Clock Ratio...................:
CPU Frequency.....................:
CPU Host Clock Control............:
CPU Host Frequency(Mhz)...........:
PCI Express Frequency (Mhz).......:
C.I.A.2...........................:
Performance Enhance...............:
System Memory Multiplier (SPD)....:
Memory Frequency(Mhz).............:
DRAM Timing Selectable ...........:
[B]Standard Timing Control[/B]
CAS Latency Time (tCL)............:
DRAM RAS# to CAS#  (tRCD).........:
DRAM RAS# Precharge (tRP).........:
Precharge Delay (tRAS)............:
[B]Advanced Timing Control[/B]
ACT to ACT Delay(tRRD)............:
Rank Write to READ Delay (tWTR)...:
Write To Precharge Delay (tWR)....:
Refresh to ACT Delay (tRFC).......: 
Read To Precharge Delay (tRTP)....: 
Static tREAD Value (tRD)..........:
Static tREAD Phase Adj............: 
Command Rate (CMD)................:
[B]Clock Driving and Skew Control[/B]
CPU/PCIEX Clock Driving Control...:
CPU Clock Skew Control............: 
(G)MCH Clock Skew Control.........: 
[B]System Voltage Control[/B] () = Base Voltages
DDR3 OverVoltage Control...(1.50v):
PCI-E OverVoltage Control.,(1.50v):
FSB OverVoltage... 65nm = 1.25v..+:
(G)MCH OverVoltage Control,(1.25v):
CPU GTLREF1 Voltage*.......(67%)..:
CPU GTLREF2 Voltage*.......(61%)..:
Loadline Calibration..............:
CPU Voltage Control...............:
Normal CPU Vcore..................:
Note: * Hidden Features Press [CTRL] + [F1] from main Menu to Access + FSB 45nm= 1.15v
[B][U]Advanced Bios Features[/U][/B]
CPU Multi-Threading...............:
Limit CPUID Max to 3..............:
No-Execute Memory Protect.........:
CPU Enhanced Halt(CIE)............:
CPU Thermal Monitor 2.............:
CPU EIST Function.................:
Virtuaalization Technology........: 

[supershanks]

[B][U]GIGABYTE GA X48 DQ6 Clock Settings[/U][/B]

[B][U]MB Intelligent Tweaker (MIT)[/U][/B]
Robust Graphics Booster...........:
CPU Clock Ratio...................:
CPU Frequency.....................:
CPU Host Clock Control............:
CPU Host Frequency(Mhz)...........:
PCI Express Frequency (Mhz).......:
C.I.A.2...........................:
Performance Enhance...............:
System Memory Multiplier (SPD)....:
Memory Frequency(Mhz).............:
DRAM Timing Selectable ...........:
[B]Standard Timing Control[/B]
CAS Latency Time (tCL)............:
DRAM RAS# to CAS#  (tRCD).........:
DRAM RAS# Precharge (tRP).........:
Precharge Delay (tRAS)............:
[B]Advanced Timing Control[/B]
ACT to ACT Delay(tRRD)............:
Rank Write to READ Delay (tWTR)...:
Write To Precharge Delay (tWR)....:
Refresh to ACT Delay (tRFC).......: 
Read To Precharge Delay (tRTP)....: 
Static tREAD Value (tRD)..........:
Static tREAD Phase Adj............: 
Command Rate (CMD)................:
[B]Clock Driving and Skew Control[/B]
CPU/PCIEX Clock Driving Control...:
CPU Clock Skew Control............: 
(G)MCH Clock Skew Control.........: 
[B]System Voltage Control[/B] () = Base Voltages
DDR3 OverVoltage Control...(1.50v):
PCI-E OverVoltage Control.,(1.50v):
FSB OverVoltage Control....(1.10v):
(G)MCH OverVoltage Control,(1.45v):
CPU GTLREF1 Voltage*.......(67%)..:
CPU GTLREF2 Voltage*.......(61%)..:
Loadline Calibration..............:
CPU Voltage Control...............:
Normal CPU Vcore..................:
Note: * Hidden Features Press [CTRL] + [F1] from main Menu to Access
[B][U]Advanced Bios Features[/U][/B]
CPU Multi-Threading...............:
Limit CPUID Max to 3..............:
No-Execute Memory Protect.........:
CPU Enhanced Halt(CIE)............:
CPU Thermal Monitor 2.............:
CPU EIST Function.................:
Virtuaalization Technology........: 

[supershanks]

Genie BIOS Template.

[code]
CPU Feature
Thermal Management Control: Disabled
PPM(EIST) Mode: Disabled
Limit CPUID MaxVal: Disabled
CIE Function: Disabled
Execute Disable Bit: Disabled
Virtualization Technology: Disabled
Core Multi-Processing: Enabled

Exist Setup Shutdown: Mode 2
Shutdown after AC Loss: Disabled
CLOCK VC0 divider: AUTO
CPU Clock Ratio Unlock: Enabled
CPU Clock Ratio:
Target CPU Clock:
CPU Clock:
Boot Up Clock:
DRAM Speed:
Target DRAM Speed:
PCIE Clock: 100mhz
PCIE Slot Config: 1X 1X

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
SATA Spread Spectrum: Disabled

Voltage Settings
CPU VID Control:
CPU VID Special Add:
DRAM Voltage Control:
SB Core/CPU PLL Voltage:
NB Core Voltage:
CPU VTT Voltage:
Vcore Droop Control: Enabled
Clockgen Voltage Control: 3.45v
GTL+ Buffers Strength: Strong
Host Slew Rate: Weak
GTL REF Voltage Control: Disable
x CPU GTL1/3 REF Volt: 110
x CPU GTL 0/2 REF Volt: 110
x North Bridge GTL REF Volt: 110

[size=3][b]DRAM Timing[/b][/size]
Enhance Data transmitting: AUTO
Enhance Addressing: AUTO
T2 Dispatch: Disabled

DRAM CLK Driving Strength: 
DRAM Data Driving Strength: 
Ch1 DLL Default Skew Model: 
Ch2 DLL Default Skew Model: 

Fine Delay Step Degree: 

Clock Setting Fine Delay
Ch1 Clock Crossing Setting: AUTO
DIMM 1 Clock fine delay: Current
DIMM 2 Clock fine delay: Current
Ch 1 Command fine delay: Current
Ch 1 Control fine delay: Current


Ch2 Clock Crossing Setting: AUTO
DIMM 3 Clock fine delay: Current
DIMM 4 Clock fine delay: Current
Ch 2 Command fine delay: Current
Ch 2 Control fine delay: Current

Ch1Ch2 CommonClock Setting: Auto

Ch1 RDCAS GNT-Chip Delay: Auto
Ch1 WRCAS GNT-Chip Delay: Auto
Ch1 Command to CS Delay: Auto

Ch2 RDCAS GNT-Chip Delay: Auto
Ch2 WRCAS GNT-Chip Delay: Auto
Ch2 Command to CS Delay: Auto 

CAS Latency Time (tCL):
RAS# to CAS# Delay (tRCD):
RAS# Precharge (tRP):
Precharge Delay (tRAS):
All Precharge to Act: AUTO
REF to ACT Delay (tRFC): AUTO
Performance LVL (Read Delay) (tRD): AUTO

Read delay phase adjust: Enter

Ch1 Read delay phase (4~0)
Channel 1 Phase 0 Pull-In: Auto
Channel 1 Phase 1 Pull-In: Auto
Channel 1 Phase 2 Pull-In: Auto
Channel 1 Phase 3 Pull-In: Auto
Channel 1 Phase 4 Pull-In: Auto

Ch2 Read delay phase (4~0)
Channel 2 Phase 0 Pull-In: Auto
Channel 2 Phase 1 Pull-In: Auto
Channel 2 Phase 2 Pull-In: Auto
Channel 2 Phase 3 Pull-In: Auto
Channel 2 Phase 4 Pull-In: Auto

MCH ODT Latency: AUTO
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Read to Write Delay (tRDWR): AUTO
Ranks Write to Write (tWRWR): AUTO
Ranks Read to Read (tRDRD): AUTO
Ranks Write to Read (tWRRD): AUTO
Read CAS# Precharge (tRTP): AUTO
ALL PRE to Refresh: AUTO 

[tunayx]

Asus P5K SE Bios Settings
Bios 0901
JumperFree Configuration Settings
CPU Ratio Settings :
FSB Strap North Bridge :
FSB Frequency :
PCI-E Frequency :
DRAM Frequency:
Dram Command Rate
DRAM Timings:-
CAS# Latency:
RAS# to CAS# Delay:
RAS# Precharge:
RAS# Activate to Precharge:
TWR: 
TRFC: 
TWTR: 
TRRD:
TRTP:
DRAM Static Read Control: 
Transaction Booster:
Cpu Voltage:
Cpu GTL Voltage reference:
CPU Spread Spectrum: 
PCIE Spread Spectrum: 
CPU Voltage:
CPU Voltage Reference:
DRAM Voltage: 
Clock Over-charging mode:
Cpu spread spectrum:
Pcie spread spectrum:

Advance CPU Settings
CPU Ratio Setting
C1E Suppport
Max CPUID Value Limit:
Vanderpool Technology:
CPU TM Function:
Execute Disable Bit
Intel® Speedstep™ Tech

[supershanks]

Thanks tunayx

[pistyll]

Asus P5KC Bios Settings
bios 1105
JumperFree Configuration Settings
CPU Clock : 322
Multiplier : 9
FSB Frequency : 322
PCI-E Frequency :100

DRAM Frequency: ddr2 774
Dram Command Rate 2t
DRAM Timings:-
CAS# 5
RAS# 5 dram Clocks
RAS# 5 Dram Clocks
RAS# 15 Dram Clocks
TWR: Auto
TRFC: Auto
TWTR: Auto
TRRD:Auto
TRTP:Auto
DRAM Static Read Control: Auto
Transaction Booster: Disabled
Boost Level : 0
Clock Over-Charging Mode: Auto
Level ??
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Voltage: 1.3375v
CPU Voltage Reference: Auto
Load Line Calibration: Enabled
CPU PLL Voltage: Auto
DRAM Voltage: 2.10v
FSB Termination Voltage: Auto
North Bridge Voltage: 1.40v
North Bridge Voltage Reference:
South Bridge Voltage: ??
Advance CPU Settings
C1E Support Disabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit Enabled
PECI: Not in bios
Intel® Speedstep Not in Bios

[supershanks]

Cheers pistyll , both yours & tunayx added to index