All Parts Ordered Today

[kinnsy]

Originally Posted by godsdog

^ You need a hand that shape to make the Diamondback work for you.

I don't have any problems with the thumb button on the left, the right/pinky button is a different matter altogether.

[affiliate13]

Today is a happy day, got home, took out the board, replaced the Celly with the E3110 and stripped the stock mobo cooling to clean and re-apply with OCZ freeze.

Its now all setup running prime @ 3.6 using Clunks settings from the x48 LT living review. Temps seem OK for now.

If this passes ill start going up slowly hopefully 4050 will be Ok to reach, anything extra will be a nice bonus.

[Clunk]

Originally Posted by affiliate13

anything extra will be a nice bonus.

A brucey one.

[affiliate13]

Hmm,
It will go higher into windows at 4.2 but this take 4.5v(smartguardian and cpuz read this as 4.7v) one core always fails imediately running pime95.

It seems stable at those volts for 4050, but i think that it too high for 24/7 use.

I upped the NB and CPU VTT, RAM is on 333/800@1080.

I think the chip might not be too great, temps sit at around 60c but the volts seem too high.

[Clunk]

Grab the BIOS template and list your settings

[affiliate13]

Can boot into windows, but cant prime95 for more than 15mins:
CPU Feature
Thermal Management Control: Disabled
PPM(EIST) Mode: Disabled
Limit CPUID MaxVal: Disabled
CIE Function: Disabled
Execute Disable Bit: Disabled
Virtualization Technology: Disabled
Core Multi-Processing: Enabled

Exist Setup Shutdown: Mode 2
Shutdown after AC Loss: Disabled
CLOCK VC0 divider: AUTO
CPU Clock Ratio Unlock: Enabled
CPU Clock Ratio:9
Target CPU Clock:4050
CPU Clock:450
Boot Up Clock:auto
DRAM Speed:333/800
Target DRAM Speed:1081
PCIE Clock: 100mhz
PCIE Slot Config: 1X 1X

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
SATA Spread Spectrum: Disabled

Voltage Settings
CPU ViD Control:1.43750V
CPU VID Special Add:Auto
DRAM Voltage Control:2.150V
SB Core/CPU PLL Voltage:1.510v
NB Core Voltage:1.456
CPU VTT Voltage:1.100
Vcore Droop Control: Enabled
Clockgen Voltage Control: 3.45v
GTL+ Buffers Strength: Strong
Host Slew Rate: Weak
GTL REF Voltage Control: Disable
x CPU GTL1/3 REF Volt: 110
x CPU GTL 0/2 REF Volt: 110
x North Bridge GTL REF Volt: 110

DRAM Timing
Enhance Data transmitting: AUTO
Enhance Addressing: AUTO
T2 Dispatch: Disabled

Clock Setting Fine Delay
Ch1 Clock Crossing Setting: AUTO
DIMM 1 Clock fine delay: Current
DIMM 2 Clock fine delay: Current
Ch 1 Command fine delay: Current
Ch 1 Control fine delay: Current


Ch2 Clock Crossing Setting: AUTO
DIMM 3 Clock fine delay: Current
DIMM 4 Clock fine delay: Current
Ch 2 Command fine delay: Current
Ch 2 Control fine delay: Current

Ch1Ch2 CommonClock Setting: Auto

Ch1 RDCAS GNT-Chip Delay: Auto
Ch1 WRCAS GNT-Chip Delay: Auto
Ch1 Command to CS Delay: Auto

Ch2 RDCAS GNT-Chip Delay: Auto
Ch2 WRCAS GNT-Chip Delay: Auto
Ch2 Command to CS Delay: Auto

CAS Latency Time (tCL):5
RAS# to CAS# Delay (tRCD):5
RAS# Precharge (tRP):5
Precharge Delay (tRAS):15
All Precharge to Act: AUTO
REF to ACT Delay (tRFC): AUTO
Performance LVL (Read Delay) (tRD): AUTO

Read delay phase adjust: Enter

Ch1 Read delay phase (4~0)
Channel 1 Phase 0 Pull-In: Auto
Channel 1 Phase 1 Pull-In: Auto
Channel 1 Phase 2 Pull-In: Auto
Channel 1 Phase 3 Pull-In: Auto
Channel 1 Phase 4 Pull-In: Auto

Ch2 Read delay phase (4~0)
Channel 2 Phase 0 Pull-In: Auto
Channel 2 Phase 1 Pull-In: Auto
Channel 2 Phase 2 Pull-In: Auto
Channel 2 Phase 3 Pull-In: Auto
Channel 2 Phase 4 Pull-In: Auto

MCH ODT Latency: AUTO
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Read to Write Delay (tRDWR): AUTO
Ranks Write to Write (tWRWR): AUTO
Ranks Read to Read (tRDRD): AUTO
Ranks Write to Read (tWRRD): AUTO
Read CAS# Precharge (tRTP): AUTO
ALL PRE to Refresh: AUTO





Thanks for taking a look Clunk.

[Clunk]

You'll be better off putting the RAM to 1:1 for now, 333/667.

I don't know much about that CPU, is it a Q6600 G0 equivalent? If so, depending on your cooling, 4Ghz might be a little bit over enthusiastic for 24/7

[affiliate13]

Oh sorry, it pretty much identical to the E8400. It seems nice and stable at 3.6 with 1.375V but 4G is the magic number methinks.

All suggestions appreciated.

[Clunk]

Aahh ok, 4ghz is more doable then

Still try the 333/667 and see if thats stable though.

[affiliate13]

Here you go m8: